Access Official Technical PDF

Share Summary:LinkedInEmail

In dye-sensitized solar cells (DSSCs), an electrolyte must move iodide and triiodide ions between the photoactive electrode and counter electrode. Replacing volatile liquid electrolytes with less volatile materials could address leakage and evaporation concerns, but alternative systems can introduce transport limitations. Research on phosphazene electrolytes examined how iodide salt selection affects ion conductivity, cell impedance and photovoltaic performance, offering useful lessons in electrochemical materials design.

Why electrolyte composition matters in DSSCs

A DSSC uses a dye-sensitized, porous titanium dioxide (TiO2) electrode to absorb light. The electrolyte supports redox reactions that regenerate the oxidized dye and transfer charge at the counter electrode. Both iodide (I-) and triiodide (I3-) must move through the electrolyte for this cycle to continue.

Low-viscosity liquid electrolytes can support efficient ion transport, but volatile solvents create practical concerns around containment and long-term stability. The study instead examined electrolytes based on hexa[methoxyethoxyethoxycyclotriphosphazene], or MEE-trimer, a liquid phosphazene material with negligible vapor pressure at room temperature. It also compared polymer-plasticizer blends made with methoxyethoxyethoxypolyphosphazene (MEEP) and poly(ethylene oxide) (PEO).

Because the electrolyte contains multiple mobile species, total ionic conductivity alone does not show whether the electrochemically active iodide and triiodide ions are moving effectively. The researchers combined conductivity measurements with steady-state voltammetry to estimate the contributions of individual ions, then related those measurements to solar-cell current-voltage behavior.

Phosphazene electrolytes reveal a strong salt effect

MEE-trimer electrolytes were tested with lithium iodide (LiI), sodium iodide (NaI), ammonium iodide (NH4I) and 1-propyl-3-methylimidazolium iodide (PMII). Across the tested systems, the transport of I- and I3- depended substantially on the cation paired with iodide.

The anionic conductivities followed the order PMII > NH4I > NaI > LiI. DSSC performance showed the same general ranking. At a salt concentration of 1.0 M, the PMII cell produced a short-circuit current density of 2.6 mA/cm2 and a reported power conversion efficiency of 0.92%. The corresponding efficiencies were 0.45% for NH4I, 0.22% for NaI and 0.16% for LiI.

These results illustrate why the most familiar electrolyte salt is not necessarily the best choice in a different host material. In MEE-trimer, smaller cations were considered more likely to coordinate with ether oxygen atoms. The observed conductivity trends were consistent with ion pairing and, at higher concentrations, interactions that increase viscosity and restrict ion movement. By contrast, PMII conductivity increased more steadily before beginning to level off as concentration rose.

Increasing PMII concentration also increased short-circuit current density in the tested cells. Current density rose from 2.6 mA/cm2 at 1.0 M PMII to 4.3 mA/cm2 at 3.0 M, while efficiency reached 1.3%. However, open-circuit voltage began to decline above 1.0 M. The study associated this trade-off with increased recombination between electrons and polyiodide species. Raising salt concentration may therefore improve ion transport without improving every measure of cell performance.

Impedance measurements identify multiple losses

Electrochemical impedance spectroscopy (EIS) helped separate resistance contributions within the cells. The analysis considered charge transfer at the platinum counter electrode, processes at the TiO2/dye/electrolyte interface, and low-frequency mass transport of I3- through the electrolyte.

For the MEE-trimer systems, the resistance at the platinum/electrolyte interface generally decreased in the same order as the anionic transport improved, from LiI toward PMII. This supports the view that slow regeneration of iodide at the counter electrode can restrict current. The low-frequency response also showed that triiodide mass transport was an important limitation in these relatively viscous electrolytes.

The measurements pointed to more than one potential loss pathway. Slow ion transport can hinder dye regeneration, while recombination between electrons in TiO2 and electrolyte species can reduce useful charge collection. The study therefore identifies electrolyte conductivity as a critical factor, but not the only one: interfacial charge transfer and recombination also matter.

MEEP blends compared with PEO

The polymer comparison used MEEP or PEO mixed with propylene carbonate (PC), along with PMII, iodine and an additive. MEEP/PC had a measured ionic conductivity of 2.7 mS/cm, compared with 1.7 mS/cm for PEO with an average molecular weight of 100,000 and 0.71 mS/cm for the higher-molecular-weight PEO blend.

The MEEP/PC blend also produced better photovoltaic results than either PEO/PC blend. Its reported efficiency was 1.88%, versus 1.44% for PEO100K/PC and 0.8% for PEO600K/PC. Impedance spectra showed higher internal resistance in the PEO systems, including greater low-frequency mass-transport resistance. The authors noted that phase separation in PEO/PC could contribute to slower ion transport, while the MEEP/PC blend remained homogeneous for at least a month under the reported observations.

Design implications for nonvolatile electrolytes

The practical lesson is to evaluate electrolyte formulations through both bulk transport measurements and device-level testing. A useful assessment should distinguish I- and I3- transport from total conductivity, examine interfacial resistance with EIS, and consider how salt concentration affects current, voltage and recombination.

The tested cells had relatively low efficiencies, so the findings do not establish a high-performance commercial design. They do, however, identify specific development priorities: select salts compatible with the host material, improve redox-species transport, and address recombination and blend stability. The reported MEEP/PC results also suggest that phosphazene polymers merit further investigation against conventional polymer electrolytes such as PEO.

For engineers and technical decision-makers assessing electrochemical materials, the broader point is that formulation choices shape performance through interacting transport and interface effects. In these DSSCs, PMII outperformed the other iodide salts in MEE-trimer, and MEEP/PC outperformed the tested PEO/PC blends. Further gains would depend on managing the associated trade-offs rather than optimizing conductivity alone.

Access Official Technical PDF

About The Author