Access Official Technical PDF

Share Summary:LinkedInEmail

In compound semiconductors, defects can create deep energy levels that trap carriers or accelerate their recombination. These effects can complicate the interpretation of electrical measurements and limit the usefulness of materials in applications such as radiation detection. Photo-Hall effect spectroscopy (PHES) offers a way to investigate these defects while tracking how illumination changes carrier behavior. In p-type CdMnTe, enhanced illumination made it possible to identify deep levels, determine electron and hole mobilities, and examine the origin of negative differential photoconductivity.

What photo-Hall effect spectroscopy measures

PHES combines optical excitation with Hall-effect measurements. As monochromatic light illuminates a semiconductor, photons with sufficient energy can release carriers from defect levels or generate carriers across the band gap. An applied magnetic field deflects moving carriers, producing a Hall voltage. Measuring that voltage alongside the longitudinal voltage and current reveals how the material’s conductivity and Hall mobility respond to photon energy and light intensity.

In a p-type material, holes are the majority carriers and electrons are the minority carriers. Both contribute to conductivity and the Hall signal, but their contributions differ because their concentrations and mobilities differ. This makes it difficult to infer carrier concentrations from a Hall measurement unless the relevant mobilities are known. It also makes minority-electron behavior particularly challenging to resolve when recombination rapidly removes electrons.

The study addressed this measurement challenge using a higher-flux illumination source than conventional lamp-based spectroscopy. The researchers reported that photon fluxes above 4 × 1014 cm-2 s-1 were important for revealing the electron response and correctly interpreting the defect-related features. The reported maximum filtered flux was 1.3 × 1015 cm-2 s-1 for the spectral measurements.

Using photo-Hall effect spectroscopy to identify deep levels

The PHES measurements on p-Cd1-xMnxTe showed changes in photoconductivity and Hall mobility as illumination energy increased. From the spectra, the researchers identified four deep levels: two associated with transitions from the valence band at EV + 0.63 eV and EV + 0.9 eV, and two associated with levels at EC – 1.0 eV and EC – 1.3 eV.

Identifying a threshold energy is not always enough to establish where a defect lies relative to the conduction and valence bands. Different level positions can produce transitions with similar apparent energies, but their effects on electron and hole generation differ. Comparing the photogenerated carrier concentrations therefore helps distinguish competing interpretations. In this case, the measured electron and hole responses supported a model in which the latter two levels were located relative to the conduction band, rather than the alternative positions proposed in a competing model.

The method also enabled the researchers to determine carrier mobilities from the measurements rather than relying on assumed theoretical values. Under illumination conditions where one carrier type dominated the Hall response, the reported electron mobility was 925 ± 11 cm2 V-1 s-1, and the hole mobility was 59.6 ± 0.4 cm2 V-1 s-1. These values were then used to estimate the separate electron and hole concentrations across the spectra.

How defect-assisted recombination produces negative differential photoconductivity

Photoconductivity does not necessarily rise continuously with illumination. Negative differential photoconductivity (NDPC) describes a decrease in photoconductivity as illumination increases. The measurements showed this behavior in an energy region where the electron concentration began to rise while the hole concentration decreased or saturated.

To interpret the effect, the researchers used a Shockley-Read-Hall (SRH) charge-generation and recombination model. The model accounts for carriers being captured by deep levels, thermally emitted, or generated through light-driven transitions. Its simulations supported a mechanism in which illumination generates minority electrons, which are then rapidly captured and recombine with majority holes through defect levels. The resulting loss of holes can offset the conductivity contribution from newly generated electrons.

In the proposed interpretation, both carrier-generation and recombination pathways are needed for NDPC to occur. The presence of a recombination-active defect alone is not sufficient: illumination must also generate minority carriers that can participate in the recombination process. The modeled effect depended on defect properties including carrier-capture cross sections, defect concentration, and photon-driven transition rates.

Under stronger illumination, the modeled and measured carrier behavior also illustrated the connection between NDPC and absolute negative photoconductivity (ANPC). ANPC refers to conductivity under illumination falling below its dark equilibrium value. The simulations indicated that changes to defect parameters could strengthen the reduction in hole concentration and, under some conditions, lead to this more pronounced response. Increasing defect concentration did not simply intensify NDPC; in the modeled case, a higher concentration of a particular recombination level suppressed the hole decrease.

Why the findings matter for semiconductor characterization

For engineers and technical teams evaluating semiconductor materials, the results highlight several practical points:

  • Measure both carrier types where possible. Minority-carrier mobility and concentration can be difficult to establish, especially when recombination is strong. PHES with suitable illumination conditions can help separate their contributions.
  • Use adequate photon flux. Lower-flux measurements may not produce a detectable minority-carrier signal, potentially obscuring defect-related thresholds or shifting their apparent position.
  • Interpret spectra with a physical model. Combining PHES with SRH simulations helps test whether a proposed defect-level arrangement can explain the observed electron and hole responses.
  • Assess transport under operating illumination. NDPC indicates that increased optical excitation can coincide with reduced majority-carrier concentration, so higher illumination does not necessarily mean more useful free carriers.

The study examined p-type CdMnTe, but the authors identified enhanced-illumination PHES as a potentially useful characterization approach for other semiconductor materials. Its value depends on obtaining suitable Hall signals and interpreting them in the context of carrier generation, recombination, and defect occupancy.

Conclusion

Enhanced photo-Hall effect spectroscopy provided a way to measure majority- and minority-carrier mobilities and to distinguish deep-level positions in p-type CdMnTe. When paired with SRH modeling, the measurements also connected defect-assisted recombination to negative differential photoconductivity. For semiconductor characterization, the practical lesson is to consider illumination intensity, both carrier populations, and defect-driven recombination together: each can change how a material responds to light and how its transport properties should be interpreted.

Access Official Technical PDF

About The Author