Photoconductivity in macroporous silicon depends not only on how light generates charge carriers, but also on how those carriers move and recombine near the pore surfaces. Measurements between 80 and 300 K, combined with numerical modeling, show that the porous layer and the underlying monocrystalline silicon can have distinctly different relaxation behavior. For engineers assessing porous silicon for optoelectronic components, sensors or solar-cell structures, this makes the interface and surface transport mechanisms important parts of the device picture.
Why photoconductivity relaxation matters
Photoconductivity is the change in a material’s electrical conductivity caused by illumination. After the light is switched off, excess carriers recombine or leave the regions where they were generated, and conductivity returns toward its dark value. The time-dependent return—photoconductivity relaxation—reflects the combined effects of carrier generation, diffusion, recombination and electrical fields within the structure.
Macroporous silicon has a large internal surface area. That structure can be useful in applications such as sensors and solar cells, but it also changes carrier behavior. Pore density, surface condition and passivation influence effective carrier lifetime and conductivity. The pore surface can introduce a space-charge region, where an electric field affects the movement of electrons and holes.
The study examined n-type macroporous silicon on a monocrystalline silicon substrate. Samples had an average pore diameter and spacing of about 2 μm, with pores extending approximately 100–150 μm into a 500 μm-thick sample. A 0.9 μm laser pulse was used to generate photocarriers, and relaxation was measured over temperatures from 80 to 300 K.
Photoconductivity in macroporous silicon changes with temperature
The measured relaxation curves had a substantial non-exponential component, indicating that a single decay time does not describe the response across the full interval. At room temperature, the reported photoconductivity relaxation time in macroporous silicon was hundreds of microseconds. Below 200 K, it reached tens of milliseconds. The relaxation time was also reported to be about twice that in monocrystalline silicon under the comparison described in the study.
These results reflect more than bulk recombination alone. Light-generated electron-hole pairs diffuse toward the pore-surface space-charge region. The electric field there can separate carriers: the region acts as a potential well for minority carriers and a barrier for majority carriers. Charge can accumulate at the surface, reducing the surface electrostatic field and changing the surface charge state. These coupled processes affect the measured conductivity and how quickly it relaxes.
As a result, the macropore surface is an active part of the transport system rather than a passive geometric boundary. Surface states, charge accumulation and the barrier to carrier transport all contribute to the observed kinetics.
Two photoconductivity maxima, two relaxation behaviors
Numerical calculations modeled the time-dependent distribution of excess minority carriers and specific photoconductivity through the porous layer and the silicon substrate. The model used a diffusion equation with generation, recombination and boundary conditions at the interface between the two regions. It accounted for the different effective properties of the macroporous layer and monocrystalline silicon.
The calculated distribution showed two photoconductivity maxima: one in the macroporous silicon layer and another in the monocrystalline substrate. The authors associated this pattern with light absorption, the presence of pores and carrier diffusion. Light reaching the substrate through the pores contributes to the second maximum, while absorption and diffusion help form a lower-conductivity region between the maxima.
The two maxima did not decay at the same rate. The maximum in the macroporous layer relaxed relatively rapidly, while the maximum in the monocrystalline substrate relaxed more slowly. This difference matters when interpreting an overall measurement: a signal from a composite structure can combine contributions from regions with different carrier distributions and relaxation kinetics.
Surface-barrier transport mechanisms
The analysis also considered how carriers cross or interact with the barrier at the pore surface. It distinguished three transport-recombination mechanisms:
- Thermionic emission: carriers pass over the surface barrier.
- Quantum-mechanical tunneling: carriers tunnel through the barrier to recombination centers.
- Generation-recombination in the space-charge region: carriers recombine within the region influenced by the surface electric field.
A coefficient derived from the relaxation behavior was used to identify which mechanism was more consistent with different temperature ranges. Between 240 and 300 K, the coefficient was approximately one, a result associated with thermionic-emission-controlled recombination. From 140 to 200 K, it was close to two, indicating a stronger role for generation-recombination in the space-charge region. Below 140 K, it increased sharply, pointing to a growing contribution from tunneling.
The relaxation time also varied with temperature. It changed little below 220 K, while a sharp, activation-like increase was reported over 220–260 K, with an energy of 0.31 eV. The authors additionally observed a strong relative change in relaxation time and the mechanism coefficient at low temperatures, where tunneling was indicated, and at higher temperatures, where thermionic emission was indicated.
Implications for device engineering
For engineers working with porous silicon structures, the findings highlight several considerations:
- Separate layer and substrate contributions. The porous region and the underlying silicon can have different carrier distributions and relaxation rates.
- Include surface transport in the analysis. A model based only on bulk carrier lifetime may not capture the influence of pore-surface fields, charge accumulation and recombination.
- Consider the operating temperature. The dominant barrier-related mechanism can shift with temperature, changing the interpretation of photoconductivity measurements.
- Account for non-exponential response. A single characteristic time may not adequately describe relaxation across the full structure.
Conclusion
Photoconductivity relaxation in macroporous silicon is shaped by the interaction of carrier diffusion, pore-surface electrostatics and temperature-dependent transport across surface barriers. The porous layer and monocrystalline substrate can exhibit separate conductivity maxima with different relaxation rates, while the dominant recombination mechanism changes across temperature ranges. For device characterization and modeling, the practical lesson is to treat the pore surface and substrate as distinct, coupled regions rather than assuming a uniform silicon response.