Access Official Technical PDF

Share Summary:LinkedInEmail

Plasmonic organic solar cells use metallic nanoparticles to influence how light interacts with a photovoltaic device. In a CuPc/C60 cell, adding gold nanoparticles (AuNPs) to the PEDOT:PSS hole-transport layer increased measured power conversion efficiency compared with a device without nanoparticles. The results show why nanoparticle size, optical response and layer morphology matter when evaluating materials for organic photovoltaics.

How plasmonic effects can support photovoltaic performance

Organic solar cells convert absorbed light into excitons: bound electron–hole pairs generated in the active material. For those excitons to contribute to current, they must reach a donor–acceptor interface and separate into charge carriers. The carriers then need to move through the device and be collected at its electrodes.

Localized surface plasmon resonance (LSPR) is the collective oscillation of conduction electrons in a metal nanoparticle in response to incident light at particular wavelengths. Near resonance, the local electric field around the particle can be enhanced. In a photovoltaic structure, this optical and electromagnetic response may affect light absorption in nearby active layers and the conditions for exciton generation and separation.

The study examined AuNPs dispersed in PEDOT:PSS, a transparent conducting polymer used here as a hole-transport layer. The active layers were copper phthalocyanine (CuPc), the electron donor, and fullerene C60, the acceptor. The device structure was ITO/PEDOT:PSS with or without AuNPs/CuPc/C60/aluminum.

Particle size shaped the optical response

The researchers prepared mostly spherical gold nanoparticles with average diameters ranging from 12 to 23 nm. They varied the amount of sodium citrate used in synthesis to obtain different particle sizes, then mixed the nanoparticle suspensions with PEDOT:PSS. The composite layer was spin-coated onto indium tin oxide (ITO), followed by thermal evaporation of the CuPc, C60 and aluminum layers.

UV-visible measurements showed an LSPR absorption band for each nanoparticle suspension. Across the reported samples, the peak shifted from 512 nm for 12 nm particles to 523 nm for 23 nm particles. This red shift with increasing particle size illustrates that the optical response depends on nanoparticle dimensions; particle size is therefore a relevant design variable, not just a materials characterization detail.

In the completed multilayer films, adding AuNPs increased absorbance in the 510–650 nm range, while no distinct absorption band attributable to the gold particles was observed in the device films. The study also used atomic force microscopy (AFM) to assess surface morphology. The nanoparticle-containing films showed surface features and roughness that varied across samples, with the 17 nm sample displaying the highest reported root-mean-square roughness. This is a reminder that optical changes should be considered alongside the physical quality of the deposited layers.

Measured device performance and the smallest particles

Current density–voltage measurements were conducted under illumination at 100 mW/cm2. The reference cell without AuNPs had a reported power conversion efficiency of 0.78%. With nanoparticles incorporated into PEDOT:PSS, the reported efficiency values were:

  • 12 nm AuNPs: 1.02%
  • 14 nm AuNPs: 0.95%
  • 15 nm AuNPs: 0.92%
  • 17 nm AuNPs: 0.91%
  • 19 nm AuNPs: 0.87%
  • 23 nm AuNPs: 0.84%

Among the tested sizes, 12 nm particles produced the highest reported efficiency. The short-circuit current density also rose from 5.70 mA/cm2 in the reference device to 6.61 mA/cm2 with 12 nm AuNPs. The reported open-circuit voltage and fill factor for that device were 0.44 V and 0.49, respectively.

Interpreting the proposed mechanism

The authors attribute the performance change to two connected effects. First, the transparency and conducting properties of PEDOT:PSS allow incident light to reach the CuPc layer, where additional absorption can generate excitons. Second, LSPR around the embedded AuNPs may strengthen the local electric field and contribute to the field at the CuPc/C60 interface, supporting exciton separation and subsequent charge transfer.

In practical terms, more generated excitons are useful only if they can dissociate and the resulting electrons and holes can be transported and collected. The proposed mechanism links the optical response of the nanoparticles with processes across the donor–acceptor interface and the device electrodes. However, the results apply to the specific materials, layer structure and test conditions examined; they do not establish that the same particle size or performance change will carry over to other organic photovoltaic designs.

What the results mean for materials development

For engineers and technical teams assessing photovoltaic materials, the study illustrates the value of treating an added nanoparticle layer as part of a coupled system. Particle size can affect resonance behavior, while dispersion and film morphology can influence the deposited structure. Evaluating a composite layer therefore calls for both materials characterization—such as optical spectroscopy and surface imaging—and device-level current–voltage measurements.

The central finding is specific but useful: in the tested ITO/PEDOT:PSS/AuNP/CuPc/C60/aluminum architecture, incorporating gold nanoparticles improved measured efficiency, with the best result among the tested samples occurring at 12 nm. The practical implication is to optimize nanoparticle size and layer formation together, then verify performance in the complete device rather than assuming that a stronger optical response alone guarantees better output.

Access Official Technical PDF

About The Author