Power GaN FETs are attracting attention in applications where high-voltage switching, power density and conversion efficiency must be considered together. For industrial automation, data centres and communications infrastructure, more efficient power conversion can help address system-level demands for reduced losses and compact equipment. GaN devices are also relevant to electrified vehicle powertrains, including on-board chargers and DC/DC converters.
Understanding where these devices fit requires looking beyond the semiconductor material itself. Switching behaviour, gate-drive requirements, thermal performance, reliability qualification and topology all shape whether a GaN-based design is appropriate.
Why GaN-on-Si matters for power conversion
Gallium nitride is a compound semiconductor with a wide bandgap. Compared with silicon devices, GaN power FETs can offer characteristics that support high-frequency operation at high breakdown voltages and current levels. A key manufacturing development is growing GaN epitaxial layers on large-diameter silicon substrates. This approach can reduce wafer-processing costs for power applications and enables fabrication in existing 200 mm facilities.
In switching designs, two useful comparison points are the switching figure of merit, often expressed as RDS(on) multiplied by gate-drain charge (QGD), and reverse recovery charge (Qrr). Lower values can help reduce switching losses and support higher switching frequencies. The whitepaper’s example comparison reports a reverse recovery charge of 179 nC for a GaN device and 2,790 nC for a silicon MOSFET under the stated test conditions. Such figures are specific to the devices and test setup; engineers should assess them alongside the full application requirements.
Potential benefits are not limited to switching loss. The described GaN FET features include a low-forward-voltage body diode, reverse-conduction capability, a gate threshold voltage intended to improve immunity to gate bounce, and the ability to control turn-on and turn-off slew rates. These characteristics can influence circuit design, switching behaviour and the need for external components.
Power GaN FETs in industrial and automotive systems
Power conversion efficiency and power density are important in several high-demand sectors. In industrial automation and data-centre or telecommunications infrastructure, power supplies must support substantial computing and connectivity loads. GaN-on-Si devices can be considered in power-conversion stages where fast switching and high efficiency are priorities.
Vehicle electrification is another application area. Relevant systems include on-board chargers, DC/DC converters and traction inverters. The power semiconductor selection for each stage depends on its electrical and operating requirements; GaN is one option for designs seeking a combination of high-voltage capability and power density.
For engineers evaluating a design, the practical question is how the device’s switching characteristics interact with the chosen topology, control strategy and thermal design. Lower conversion losses may reduce heat generated by the power stage, but the overall result depends on the implementation rather than on the device alone.
Topology choices: half-bridges and totem-pole PFC
Half-bridge configurations are widely used as building blocks in power conversion. GaN FETs may be applied in AC-DC, DC-DC and DC-AC systems, including multiphase inverters. The devices’ switching characteristics can also suit resonant or fixed-frequency LLC phase-shift full-bridge applications, as well as other soft-switching designs.
Totem-pole power factor correction (PFC) is a further example, particularly for hard-switching AC-DC conversion. A topology using GaN devices can reduce component count compared with some alternatives, according to the source material. Fewer components may support a more compact design, though designers still need to evaluate the complete circuit for efficiency, control, reliability and thermal performance.
GaN FETs are also relevant to AC-AC matrix converters using bidirectional switches. Across these applications, topology and operating conditions determine whether device-level advantages translate into system-level benefits.
Reliability, qualification and implementation
Introducing a newer semiconductor technology calls for careful attention to quality and reliability evidence. The whitepaper describes applying established manufacturing and quality processes, alongside application- and technology-specific testing during GaN FET development. For automotive use, it identifies extension of AEC-Q101 qualification into GaN development. These points underline the importance of assessing qualification status and reliability data for the specific device and intended application.
Gate-drive design is another practical consideration. The described devices are characterized as having straightforward gate-drive requirements, but engineers must follow the selected device’s datasheet and application guidance. Switching speed, gate bounce, transient voltage capability and dynamic on-resistance all warrant consideration during circuit design and validation.
For example, the whitepaper lists 650 V devices with maximum on-resistance values of 41 mΩ and 60 mΩ, and transient voltage capability of 800 V. These are product-specific figures, not general specifications for GaN FETs. Engineers should verify ratings, test conditions and package details against current manufacturer documentation before selecting a device.
Assessing the system-level opportunity
Power GaN FETs provide design options for high-voltage, high-frequency conversion, but selection should start with the application. Compare conduction and switching losses, operating voltage and current, thermal constraints, gate-drive needs, topology and qualification requirements. Then validate performance in the intended operating range rather than relying on a single headline parameter.
For industrial power designers and automation decision-makers, the central opportunity is to evaluate GaN where efficiency and power density are critical—while treating reliability, implementation and system-level testing as equally important. A careful, application-specific assessment is the basis for deciding whether GaN-on-Si can meet the demands of a particular conversion stage.