Access Official Technical PDF

Share Summary:LinkedInEmail

Power semiconductor devices are the switching foundation of industrial power electronics. They control how electrical energy flows through circuits used in power supplies, motor drives, heaters, lighting controls and other equipment. Understanding their internal operation and switching behavior helps engineers select components, design gate and protection circuits, and assess the voltage and current stresses a system must withstand.

The devices covered here range from components that conduct in one direction to controlled switches that operate in both directions. Their differences matter: some can be turned on by a control signal but must be turned off by the circuit, while others provide control over both transitions.

Power diodes: rectification and recovery behavior

A power diode must carry substantial forward current while blocking reverse voltage. Its construction addresses a basic trade-off: a lightly doped region supports a wide depletion layer and higher reverse blocking capability, but would create excessive forward resistance on its own. A lightly doped drift layer between more heavily doped regions helps provide the required blocking capability while supporting forward conduction.

Power diodes appear in applications such as switch-mode power supplies, choppers, snubbers and freewheeling paths. Their switching behavior also affects circuit design. During turn-on, the forward voltage can briefly rise above its steady-state value; this is known as forward recovery. During turn-off, current may continue briefly in the reverse direction. The peak reverse recovery current can add stress to the main switch in a chopper or inverter, while a rapid fall in recovery current can interact with stray inductance and produce an overvoltage. An RC snubber may be used where protection is required.

SCR thyristors: latching control of power

An SCR, or silicon-controlled rectifier, is a four-layer device with an anode, cathode and gate. Its operation is often explained using two interconnected transistors. With forward voltage applied, the device blocks current until it receives a suitable gate signal or reaches its forward breakover condition. Once regenerative action begins, the SCR turns on and its current is primarily limited by the external circuit.

The gate controls turn-on, not turn-off. After triggering, the SCR remains on when its current exceeds the latching current. To turn it off, current must fall below the holding current so stored charge can clear. In AC circuits, current may naturally fall around a supply zero crossing, a process called natural or line commutation. DC circuits require a means of forcing current below the holding level.

This latching behavior makes SCRs useful for power control, switching, pulse circuits, battery-charging regulators and overvoltage protection. Designers must also consider turn-on and turn-off times, gate-pulse duration, temperature effects and the circuit’s commutation method.

DIACs and TRIACs for bidirectional AC control

A DIAC is a two-terminal bidirectional switching device. It blocks current until the applied voltage reaches its breakover level in either polarity, then switches into conduction. Its symmetrical behavior makes it a common trigger component in DIAC-TRIAC phase-control circuits.

A TRIAC can conduct in both directions and is functionally similar to two thyristors connected in antiparallel. Its three terminals are MT1, MT2 and gate. A gate pulse can trigger conduction during either AC half-cycle, allowing control of the portion of each cycle delivered to a load. Adjusting the TRIAC conduction angle is the basis of the lamp-dimming and heater-control circuits described in the source material. TRIACs are also used with power-frequency AC loads such as motors. Their bidirectional operation is convenient, although the device’s conduction paths interact, and its ratings and on-state voltage drop differ from those of a comparable thyristor.

Transistor switches: BJT and power MOSFET

Power BJT

A power bipolar junction transistor uses base current to control collector-emitter current. In switching applications, it operates in cutoff as an open switch and in saturation as a closed switch. Adequate base drive is important: insufficient base current can leave the transistor outside saturation, increasing the voltage across it while current flows and raising power dissipation. The required drive should be assessed against the expected collector current and the transistor’s specified current gain.

Power MOSFET

A power MOSFET is controlled by gate-source voltage. When that voltage exceeds the threshold, an inversion layer forms a conductive channel between source and drain. Below threshold, the device is in cutoff; in the ohmic region, it conducts with an on-state resistance. That resistance contributes to conduction losses, and it decreases as gate-source voltage increases within the device’s permitted limits.

Power MOSFETs are used as switches and in switched-capacitor circuits. In discrete-time filters, switches transfer charge into and out of capacitors. Such circuits rely on capacitance ratios and switching frequency rather than precise absolute component values, an approach suited to integrated-circuit implementation.

GTOs and IGBTs in power conversion

A gate-turn-off thyristor (GTO) combines a thyristor-like structure with the ability to turn off through a negative gate signal. During turn-off, the gate extracts carriers from the device. Current does not disappear immediately: a tail current can persist as excess carriers in the base region recombine. GTOs have been used in variable-speed motor drives, high-power inverters, static VAR compensators, traction and high-power AC/DC supplies.

An insulated-gate bipolar transistor (IGBT) combines an insulated gate with carrier injection in the drift region. Its gate-emitter voltage controls channel formation, so the input behaves essentially like that of a MOSFET. Injected minority carriers increase conductivity in the drift region, reducing its contribution to the on-state voltage drop compared with a comparable MOSFET. IGBT construction balances voltage-blocking capability, conduction behavior and the risk of unwanted latch-up.

Practical implications for industrial designers

Device selection starts with the circuit’s operating conditions and switching requirements. Compare the required blocking voltage and current with the behavior of the candidate device, then account for turn-on and turn-off processes, gate-drive needs, commutation and protection. A device’s role in the circuit matters as much as its basic category: reverse recovery can affect a power switch, SCR turn-off depends on current falling below its holding value, and a MOSFET’s conduction loss is tied to on-state resistance.

For industrial automation engineers and system integrators, these distinctions help connect component choice to reliable control design. Understanding how each device turns on, conducts and recovers provides a sound basis for specifying power stages, designing drive circuits and identifying where switching stresses need attention.

Access Official Technical PDF

About The Author