Access Official Technical PDF

Share Summary:LinkedInEmail

Printed organic operational amplifiers offer a potential route to adding analog signal processing to lightweight, flexible and disposable sensing systems. A reported complementary organic circuit demonstrated operation from a 5 V supply, power consumption below 150 nW and an open-loop gain of up to 60. The results are relevant to engineers considering how sensor signals might be conditioned in compact electronics without relying on conventional silicon circuitry for every analog function.

The significance is not simply that an amplifier can be printed. An operational amplifier (OPA) can perform many circuit functions depending on how its output is connected back to its inputs. That versatility makes it a useful building block for sensor interfaces and other electronic systems where signals need to be amplified, converted or shaped.

Why low-voltage printed analog circuits matter

Printed electronics uses processes such as inkjet printing to pattern functional materials into electronic devices. Compared with conventional fabrication approaches, printing can avoid vacuum processing and photolithography for some device layers. Organic semiconductor devices can also be processed at relatively low temperatures, making them relevant to flexible and large-area electronics.

Potential applications include flexible displays, sensor sheets, wireless tags and biosensors. These systems often need analog circuits: sensors produce analog outputs, while radio-frequency signals also require analog processing. Yet earlier printed organic OPAs had generally required supply voltages above 40 V, limiting their suitability for mobile or bio-sensing applications where a compact, low-voltage source is preferred.

The reported circuit addressed that constraint by operating at a total supply voltage of 5 V, provided as +2.5 V and −2.5 V rails. Its measured power consumption was less than 150 nW. A supply in this range can be compatible with common mobile-electronics power arrangements, although practical integration still depends on the requirements of the complete system.

How the printed organic operational amplifiers were built

The OPAs used complementary organic thin-film transistors (OTFTs): p-type and n-type devices combined in a two-stage amplifier circuit. The semiconductor layers were solution-processed, and silver electrodes and interconnections were inkjet-printed. The n-type transistors used a dual-gate structure, while the p-type transistors used a single-gate structure.

The dual-gate design was important to circuit performance. In the reported devices, it improved the n-type transistors’ subthreshold slope and current saturation characteristics. These properties affect how sharply a transistor switches and how consistently it behaves as voltage changes. Improving them helped the amplifier achieve a steeper response and reduced hysteresis compared with a version using single-gate n-type devices.

The printed OPA had a maximum open-loop gain of 60. Open-loop gain describes how strongly the circuit responds to the voltage difference between its two inputs when no feedback path is applied. The researchers also packaged the circuit in a dual inline package for easier prototyping, demonstrating a way to connect the printed device to conventional test circuits.

Feedback turns one amplifier into several circuit functions

An OPA’s usefulness becomes clearer when negative feedback is added. In a feedback circuit, part of the output is returned to the inverting input, helping set the circuit’s behavior. For an engineer, this means that external resistors and capacitors can configure the same core amplifier for different signal-processing tasks.

Amplification and buffering

Configured as a voltage follower, the circuit produced an output that closely tracked its input, with a measured closed-loop gain of 0.99 ± 0.01 and an offset below 0.05 V. A voltage follower can help transfer a signal from a high-impedance source without requiring the source itself to drive a more demanding circuit.

In a non-inverting amplifier, resistors in the feedback network set the gain. The reported circuit achieved a closed-loop gain of 1.8 with equal 100 MΩ resistors, and gains as high as 8.2 as the feedback resistance was increased. This resistor-defined gain is useful because it can be adjusted through circuit design rather than depending only on variable transistor characteristics.

Mathematical operations and signal conversion

Adding a capacitor to the feedback network enabled integration: a rectangular input signal produced a triangular output. A differentiator configuration did the reverse, converting a triangular input into a rectangular output. These functions can shape signals before further processing, though their practical use depends on the signal frequency and the surrounding circuit.

The OPA also worked as a current-to-voltage converter, also called a transimpedance amplifier. With a 1 GΩ feedback resistor, the demonstrated conversion ratio was 109 V/A. This function is relevant to sensors that produce a current output, including the amperometric biosensor application discussed by the researchers.

Additional demonstrations included a triangular-wave oscillator and a pulse-width-modulated rectangular output. The pulse-width modulation duty ratio could be controlled by a DC input voltage. The circuit was also demonstrated as a comparator, switching its output according to the relative voltages at its inputs.

Performance considerations for system designers

The reported gain-bandwidth product was 50 Hz, and a closed-loop non-inverting amplifier maintained a gain of five over the measured range of 0.1–10 Hz. These results define an important boundary for potential uses: the demonstrated circuit supports low-frequency signal processing, but the data do not establish suitability for faster control loops or higher-bandwidth instrumentation.

The work therefore represents a circuit-level demonstration, not evidence that printed organic OPAs can replace silicon amplifiers across industrial applications. Engineers evaluating the technology should consider the required bandwidth, signal range, sensor interface, environmental conditions and integration needs of the target system. Further improvements to transistor dimensions and printing resolution were identified as possible routes to higher-frequency performance.

Practical implications

Printed organic operational amplifiers show how a single low-voltage circuit can support multiple analog functions using external passive components. Their demonstrated 5 V operation and micropower consumption make them relevant to research and development in compact sensing and printed electronics, particularly where flexible or disposable form factors are being explored.

For automation engineers and system integrators, the practical takeaway is to assess this technology against specific low-frequency sensing requirements rather than assume it is a general-purpose substitute for established analog components. The demonstrated versatility is promising, while bandwidth and application-specific integration remain essential design considerations.

Access Official Technical PDF

About The Author