Access Official Technical PDF

Share Summary:LinkedInEmail

A programmable motion controller can provide a dedicated layer of positioning and speed control between a machine’s supervisory controls and its motors. The Autonics PMC-2HSP/2HSN series illustrates this approach: each unit controls two pulse-input stepper or servo motor axes, runs motion commands from internal memory, and connects to a PC or external control equipment. Understanding its operating modes, interfaces and safety provisions helps engineers determine how this type of controller fits into a machine architecture.

What a programmable motion controller does

The PMC controller generates pulse outputs to command motor position and speed. Its position range is -8,388,608 to +8,388,607, and its specified run-speed range is 1 pulse per second to 4 million pulses per second. It supports one-pulse or two-pulse output types through line-driver outputs. These capabilities are intended for pulse-commanded stepper motors or servo drives; the controller is not described as a general-purpose motor power drive.

Each controller has two axes. In an RS485 configuration, up to 16 nodes can be connected, allowing control of as many as 32 axes in total. Each RS485 node needs its own ID; duplicate IDs can cause malfunction or product damage. The series also supports USB and RS232C communications, with the specific interfaces depending on the model.

Choosing an operating mode

The controller can be operated from a PC using MotionStudio or through its Parallel I/F. In the PC arrangement, MotionStudio acts as the master and the motion controller as the slave. The Parallel I/F provides a way for external signals, such as those from a sequence controller or switches, to initiate motion without relying on a PC for each operation.

Available run modes support different control tasks:

  • Index mode: Selects from configured motion indices, with 64 assignable index numbers.
  • Jog mode: Supports directional movement for setup or operation, with mode and speed selections handled through configuration and I/O signals.
  • Continuous mode: Runs continuous pulse motion, with direction and speed selection available through the Parallel I/F.
  • Program mode: Executes stored commands, including absolute and relative moves, home search, timers, jumps, repetitions and I/O operations.

The controller can store up to 200 program steps. Its command set allows a sequence to combine movement with waits for external inputs or changes to general-purpose outputs. This can make it possible to coordinate basic machine actions within the motion program, while the larger control system remains responsible for overall machine logic as required by the application.

Interpolation and homing

The PMC-2HSP series adds two-axis interpolation functions; these are not listed for the PMC-2HSN series. Linear interpolation coordinates movement across two axes, while the available circle and circular interpolation commands support specified clockwise or counterclockwise paths. Selection between models should therefore account for whether coordinated two-axis paths are required, rather than assuming every model has the same motion functions.

For repeatable positioning, the controller provides a four-step home-search function: high-speed near-home search, low-speed home search, low-speed encoder Z-phase search, and high-speed offset movement. The relevant inputs include near-home, home and Z-phase signals. A machine’s sensor arrangement and desired reference procedure need to be reflected in the home-search settings and wiring.

Plan I/O and communications carefully

Integration involves more than connecting the motor drivers. The controller provides a Parallel I/F, separate X- and Y-axis I/O connectors, and general-purpose inputs and outputs. Axis connectors include drive pulse outputs, limit inputs, emergency-stop input, home-search inputs and general-purpose I/O. Parallel I/F signals can have different functions depending on the selected run mode, so engineers should verify the signal assignment and timing requirements for the intended configuration.

Communications choice also affects the system layout. USB and RS232C can connect a PC for setup or operation, while RS485 supports multiple controller nodes. The specified supply is 24 VDC ±10%, with maximum power consumption of 6 W. Sensor power is provided at the I/O connectors, but the manual limits the total draw across the listed connectors to less than 300 mA. Confirm wiring, connector specifications, node addressing and the relevant model’s interfaces before commissioning.

Safety and commissioning considerations

Motion-control behavior must be considered alongside machine safeguarding. The controller’s reset and emergency-stop inputs can stop motion immediately, but an immediate stop during high-speed operation may cause injury or product damage. They should not be treated as substitutes for a machine-level safety design. The manual calls for fail-safe devices when the unit is used with specified high-risk machinery and advises planning for power failure.

Before energizing the system, check supply polarity and input specifications, secure power and signal wiring, and keep signal cables separated from power and load wiring where possible to reduce noise-related malfunction. Do not wire, inspect or repair the unit while power is applied. Configure limit behavior, home-search logic and I/O signal levels, then verify operation under controlled commissioning conditions.

Conclusion

A programmable motion controller can consolidate two-axis pulse motion, stored sequencing, homing and machine I/O in a dedicated device. The practical integration decision depends on the required motion functions—especially whether interpolation is needed—the selected communications method, the external control strategy and the machine’s safety architecture. Matching those requirements to the controller’s model and configuring its signals deliberately provides a clearer path from system design to reliable commissioning.

Access Official Technical PDF

About The Author