Trace analysis often depends on more than a sensitive detector: the sensing material must also distinguish the target from other substances in a sample. A propranolol fluorescence sensor described in an analytical study combines molecular imprinting with carbon dots to address both needs. The design is relevant to engineers and technical decision-makers evaluating optical sensing concepts, although the reported work concerns analytical chemistry rather than an industrial process-control application.
Why combine fluorescence with molecular recognition?
Propranolol is a beta-blocker used to treat conditions including high blood pressure, arrhythmias and angina. It can also be misused as a doping agent. Established methods for measuring it include chromatography, spectrophotometry, electrochemical techniques and chemiluminescence. Depending on the method, analysis may involve sample preparation, longer processing time, higher cost, or limitations in sensitivity and selectivity.
Fluorescence sensing offers a different approach: a material produces an optical signal that changes when the target interacts with it. But a fluorescent response alone does not guarantee that the sensor will recognize the intended molecule in the presence of other compounds. The study addressed this challenge by pairing fluorescent carbon dots with a molecularly imprinted polymer (MIP), a material engineered to recognize a selected molecule.
How the propranolol fluorescence sensor works
Carbon dots provide the optical signal
The sensor’s fluorescent component consists of carbon dots (CDs) synthesized hydrothermally from Cedrus plant material. Carbon dots are fluorescent carbon-based nanomaterials. The paper identifies properties that make them of interest for sensing, including aqueous solubility, surface functionalization and fluorescence stability. The authors present them as an alternative to quantum dots, whose toxicological effects on people and the environment are a concern.
In the reported measurements, the carbon dots had an average size of 5.3 nanometres based on transmission electron microscopy; dynamic light scattering gave a mean diameter of 5.5 nanometres. Their maximum excitation and emission wavelengths were 340 and 420 nanometres, respectively. These values describe the study’s material and measurement setup, not a universal specification for carbon-dot sensors.
Imprinting creates selective binding sites
The carbon dots were coated with a thin molecularly imprinted layer using a reverse microemulsion and a sol-gel process. Propranolol served as the template molecule during fabrication. In simplified terms, the template helps form cavities in the polymer that correspond to its shape and chemical interaction points. After the propranolol was extracted, those sites could bind the target again.
The coating process used tetraethoxysilane (TEOS) to form a silica layer and 3-aminopropyltriethoxysilane (APTES) as a functional component. During preparation, interactions between APTES and propranolol helped organize the recognition sites. Once the template was removed, propranolol could rebind through non-covalent interactions. A non-imprinted polymer-coated carbon-dot material was also prepared as a comparison, without propranolol in the fabrication step.
Fluorescence quenching indicates target binding
When propranolol binds to the imprinted material, the carbon dots’ fluorescence decreases, a change known as quenching. The sensor determines concentration by comparing the fluorescence signal before and after exposure to the target. The study used the difference between these measurements, F0–F, to build its calibration relationship.
The authors considered energy transfer and electron transfer as possible explanations for the quenching. Because the propranolol absorption spectrum did not overlap with the carbon-dot fluorescence spectrum, they concluded that energy transfer was not supported by the spectral results; charge transfer was considered more likely. This interpretation explains the proposed signal mechanism, while the practical measurement relies on observing the fluorescence change.
Reported analytical performance and operating conditions
Under the study’s optimized conditions, the response was linear for propranolol concentrations from 0.8 to 65.0 nanomoles per litre, with a reported detection limit of 0.2 nanomoles per litre. Measurements used a buffer at pH 7, a temperature of 25°C and a six-minute incubation period. The signal reached an approximately stable level after six minutes under the tested conditions.
Selectivity was assessed by testing compounds and ions including glucose, dopamine, tryptophan, magnesium, potassium, cysteine, ascorbic acid, atenolol and pindolol alongside propranolol. The imprinted sensor showed a more selective response than the non-imprinted composite and uncoated carbon dots. This comparison highlights the role of the recognition layer: the fluorescent material supplies the signal, while the imprinted cavities help differentiate the target.
The method was also evaluated using human plasma samples. Sample preparation involved adding trichloroacetic acid to remove proteins, followed by centrifugation. The reported recovery tests provide evidence of performance in that specific prepared sample matrix. They do not, by themselves, establish suitability for other sample types or routine industrial monitoring.
What engineers can take from the design
For automation and instrumentation teams, this work illustrates a broader sensor-development principle: combine a transduction method with a material designed for target recognition. In this case, fluorescence provides an optical readout, while molecular imprinting supplies selectivity. The approach may be of interest when evaluating compact analytical methods, but moving from a laboratory measurement to a field or production setting would require application-specific validation.
- Separate signal generation from selectivity: the carbon dots fluoresce, while the imprinted polymer is designed to bind propranolol.
- Account for sample preparation: the reported plasma procedure included protein removal, so the analytical result should be considered alongside preparation requirements.
- Match operating conditions: pH, temperature, sensor-material concentration and incubation time affected the measured response.
- Validate the intended matrix: selectivity and recovery results from the tested conditions should not be assumed to transfer automatically to other samples.
Conclusion
The propranolol fluorescence sensor pairs Cedrus-derived carbon dots with a molecularly imprinted silica-based coating. Rebinding reduces fluorescence, enabling concentration measurements across a reported low-nanomolar range. Its main technical lesson is the value of integrating a measurable optical signal with selective molecular recognition. For engineers assessing analytical sensing options, the design is a useful example of that principle, while its practical adoption would depend on validation for the target sample, operating environment and measurement workflow.