Access Official Technical PDF

Share Summary:LinkedInEmail

Radiation-tolerant power management is a system-level challenge: spacecraft electronics must manage power conversion and distribution while continuing to operate in a radiation environment. A power management and distribution (PMAD) architecture has to coordinate its sources, converters, battery and loads, and detect conditions that could threaten reliable operation. One approach presented at AMICSA 2018 combines a radiation-hardened analog front end (AFE) with FPGA-based control to handle sensing, switching and protection functions.

What a spacecraft PMAD system must coordinate

A PMAD system transfers energy from its sources to the spacecraft’s electrical loads and manages power moving to and from the battery. Its main functions include DC/DC conversion, protection and power transfer, with fault management performed both locally and remotely. In the architecture described, photovoltaic (PV) module strings provide the input sources.

Each string is paired with a boost DC/DC converter. The converters operate independently to seek the maximum power point (MPP) for their respective strings, while delivering power to a shared distribution bus. Independent tracking matters to the architecture because the operating conditions that affect a string—including illumination angle, shading and temperature—can vary. Maximum power point tracking (MPPT) adjusts converter operation to follow the MPP as conditions change.

The system monitors electrical and thermal conditions to support control and protection. Voltage is measured at input and output nodes, and current is monitored through each converter. Temperature is also measured at selected points. In addition, arc-fault detector circuits are assigned to each string to detect arcing on high-current or high-voltage rails.

Dividing sensing and control between the AFE and FPGA

The design separates the interface to power hardware from the system-level control logic. The AFE converts sensor signals to digital values and drives the power MOSFETs using pulse-width-modulated (PWM) signals generated digitally. An FPGA implements DC/DC converter control, MPPT, and power and safety management. A communication function can support remote management.

This division gives the system distinct roles. The AFE provides the electrical interface between monitored signals, digital control and the switching devices. The FPGA processes the control tasks that coordinate converter operation and system protection. Rather than treating power conversion as an isolated circuit, the arrangement connects measurements and switching to a broader control and safety function.

For engineers, the interface between these elements is a key design boundary. The AFE must receive the relevant sense lines and drive the MOSFETs, while the FPGA uses the resulting signals in its control functions. The architecture also assigns protection functions to the same control system, linking power regulation with decisions about safe operation.

Radiation effects require system-level attention

Radiation can affect the electrical behavior of the AFE. The AMICSA paper specifically highlights parametric drift in the front end and considers how system design can alleviate its effects. This is an important distinction: choosing a radiation-hardened IC is only one part of designing a fault-tolerant power system. The behavior of that IC within its sensing and control loops also matters.

In practice, designers need to consider how changes in the AFE’s parameters could influence the measurements and drive signals used by the rest of the PMAD system. The architecture makes the AFE part of several critical paths: it reads voltage and current sense lines and drives MOSFETs. Its role therefore connects radiation behavior with converter operation and system-level protection. The paper identifies system design as a mitigation route, but the available description does not specify a particular compensation method or quantitative drift limits.

That limitation is a useful reminder for project teams: radiation-hardening claims, component characterization and system behavior should be assessed together. A component’s radiation response needs to be considered in the context of the functions it performs and the control architecture around it. The design also needs clearly defined responsibilities for local and remote fault management.

Extending protection from converters to loads

Protection in the proposed topology is not limited to the power source and conversion stage. Loads connect to the distribution bus through individual circuits that provide current and safe-operating-area (SOA) protection and interface with the FPGA. Battery power transfer is also part of the PMAD function. Together, these elements show how sensing, conversion, source tracking and load protection can be organized within one coordinated architecture.

  • At the source: PV strings feed independent boost converters, with MPPT applied per string.
  • At the conversion stage: monitored voltages and currents support digital converter control.
  • At the distribution bus: protected connections manage power delivery to individual loads.
  • Across the system: temperature monitoring, arc detection and fault management contribute to power and safety functions.

This functional view can help teams review whether each measurement and protection function has a defined place in the control scheme. It also makes the relationship between the AFE, FPGA, MOSFETs and power devices easier to evaluate during architecture development.

Practical implications for system designers

For spacecraft electronics teams, the architecture highlights several decisions to address early: how inputs are divided among converters, how sensing is routed to the AFE, which control tasks are assigned to the FPGA, and how protection is applied to strings and loads. Radiation-related parametric drift should be considered alongside those decisions, because the AFE links the physical power stage to digital control.

Ultimately, fault tolerance depends on more than selecting individual components. The PMAD system must bring together power conversion, monitoring, control and protection in a way that accounts for the operating environment. An AFE paired with FPGA control provides one framework for organizing those functions, while system-level analysis remains essential to understanding how radiation effects could influence the complete power path.

Access Official Technical PDF

About The Author