Access Official Technical PDF

Share Summary:LinkedInEmail

Remote station power systems must do more than supply electricity: they must keep sensors, communications and supporting equipment operating where grid access is unavailable and maintenance visits are difficult. Environmental monitoring stations offer useful lessons for industrial automation teams designing autonomous equipment in isolated or harsh locations. The central challenge is balancing energy demand with locally available generation, storage capacity and the practical limits of servicing the installation.

A station may consume only a modest amount of power, but an interruption can stop measurements or data transmission. Reliable design therefore starts with the full load—not just the primary instrument—and accounts for periods when generation is reduced or unavailable.

Start with the load and site conditions

Estimate the total electrical demand of every component: sensors, data acquisition, communications, heating and alarms. Then consider the site’s energy resources, seasonal conditions, installation space and access for maintenance. A system that performs well in one location may be unsuitable in another because sunlight, wind, snow, temperature and terrain vary.

Intermittent generation makes storage and autonomy important design questions. Battery capacity should reflect the expected load and the number of days the station may need to operate without useful generation. Solar array sizing, meanwhile, depends on the site’s solar potential, shading, available space and logistics such as equipment weight. The design must consider the least favourable season, rather than relying only on average or summer conditions.

Choosing generation for remote station power systems

Photovoltaic solar

Photovoltaic panels are widely used for autonomous stations because they require little routine maintenance. Their output depends on irradiance, orientation, tilt, temperature, cleanliness and shading. Cold conditions can benefit panel performance, but snow or dirt can obstruct incoming light. In series-connected cells, shading on part of a panel can restrict current through the circuit; installation layout and bypass diodes can help mitigate this effect.

Panel angle should reflect the site and operating season. A fixed array is often more appropriate than a tracking system for an unattended station: trackers add moving parts, can be vulnerable to strong winds and consume some of the energy they produce. Where local conditions support it, a fixed array can instead be sized to provide a suitable energy margin.

Wind, water and fuel cells

Small wind turbines can complement solar where wind is a useful resource, including periods with limited sunlight. However, actual output depends on the installation environment. Turbulent, angled winds can reduce the performance of some turbine designs compared with controlled wind-tunnel conditions. Mechanical components also require inspection, and secure mounting is important at exposed sites where maintenance is infrequent.

Hydro turbines can provide a steady source where flowing water is available, but their suitability is site-specific. Methanol fuel cells offer another option for continuous generation, with fuel storage supporting extended autonomy. Their use brings trade-offs: fuel must be transported and handled safely, and emissions, ventilation and cold-weather operation must be considered. A hybrid arrangement can combine generation sources and batteries, but each added component also needs to be managed and maintained.

Battery storage and cold-weather operation

Lead-acid batteries are commonly used in autonomous stations, including sealed valve-regulated lead-acid (VRLA) types. Their usable capacity is affected by discharge rate, temperature, charging and age. Cold reduces available capacity, while excessive discharge can shorten service life. System sizing should therefore distinguish a battery’s rated capacity from the amount intended for routine use.

For lead-acid systems, the guidance in the report recommends avoiding deep discharge where possible and recharging batteries that are stored for extended periods. Battery selection should match the application, including low-current loads and repeated charging from sources such as photovoltaic panels. Cold conditions deserve particular attention: battery performance can decline substantially, and testing under controlled low temperatures showed why field assumptions should be checked against the expected operating environment.

Lithium batteries have higher energy density and can support faster charging, but they have different charging requirements and may not be charged below 0°C. They also require suitable chargers and careful consideration of transport. The chemistry and operating temperature range should be matched to the installation rather than selected on energy density alone.

Regulation, wiring and practical reliability

Generation cannot always be connected directly to a battery or load. Charge controllers regulate voltage and current so that energy can be stored appropriately. For solar systems, maximum power point tracking (MPPT) controllers adjust operation to capture available panel power; pulse-width modulation (PWM) controllers use a simpler approach. The report recommends MPPT for scientific applications, including smaller arrays, based on its evaluations.

Wiring is another system-level consideration. Electrical resistance creates voltage drop and power loss, which increase with current and wire length. Selecting an adequate conductor cross-section helps limit those losses, particularly in low-voltage installations where current can be significant for the power delivered. Controller settings, battery charging and cable sizing should be treated as parts of one integrated design.

Design for maintainability, not just peak output

A robust remote installation is built around realistic operating conditions, not a single component’s rated output. Document the load, generation assumptions, battery autonomy and maintenance requirements. Check exposure to shading, snow, turbulence and low temperatures, and provide a practical way to inspect the system’s condition. Where the consequences of losing power are significant, consider whether separate battery packs or complementary generation sources are appropriate for the station’s needs.

The practical lesson for industrial automation is clear: dependable off-grid operation comes from matching generation, storage and regulation to the site and load as a whole. Solar is often attractive for its low maintenance, while wind, hydro and fuel cells may suit specific conditions. Careful sizing, cold-weather planning, sound wiring and accessible monitoring help keep remote equipment operating when routine intervention is not an option.

Access Official Technical PDF

About The Author