Access Official Technical PDF

Share Summary:LinkedInEmail

For process operations where gas composition needs to be monitored continuously, the Rosemount CT5100(Ex) gas analyzer combines laser spectroscopy with an enclosure designed for use in potentially explosive environments. It can detect and measure up to 10 gas types in process streams, with concentrations ranging from parts per million (ppm) to percentage levels. For engineers and operations teams, using the analyzer effectively means understanding both its measurement role and the installation and safety conditions that govern its operation.

How the Rosemount CT5100(Ex) gas analyzer works

The CT5100(Ex) is an electronic sensor that analyzes process gas using laser spectroscopy. In this approach, laser light interacts with the gas sample, and the analyzer uses that interaction to determine gas concentrations. The manual identifies quantum cascade, interband cascade and diode lasers as possible laser types in the system. The specific configuration can vary; the manual describes a maximum of six lasers per system.

The analyzer is intended to measure multiple gas species across a broad concentration range, from ppm levels to percentages. The gas stream is routed through the analyzer’s gas-handling and optical systems for measurement. Correct sample routing matters beyond measurement: the sample return must lead back to the process stream or discharge somewhere that will not create a hazard.

Designed for hazardous-area applications

The “Ex” designation reflects the analyzer’s intended use in potentially explosive environments, subject to the applicable certification, installation conditions and safe-use instructions. The April 2022 reference manual describes compliance with a range of standards and regulatory frameworks, including IEC, ATEX, UKEx and North American requirements. Site teams should verify the approvals and conditions applicable to the particular analyzer and installation rather than treating a general product description as a substitute for its nameplate, certification documents or local requirements.

The enclosure uses pressurization and purging as part of its protection approach. The purge controller monitors enclosure pressure and can output fault conditions. The manual places responsibility on the end user to connect the relevant alarm contact or signals to a suitable facility, such as a monitored alarm or automatic shutdown system. This makes the analyzer’s protection dependent not only on its enclosure but also on correctly configured site utilities, alarm handling and operating procedures.

Installation conditions to verify

Before installation, confirm the application, site conditions and analyzer variant against the product documentation. The manual specifies different maximum sample-gas temperatures by region: up to 160 °C for the European conditions described and up to 80 °C for North American conditions. These limits should not be blended into a single operating value; the applicable certification and installation requirements determine which conditions apply.

Other installation considerations include:

  • Pressurizing air: The on-site supply must provide at least 25 L/min for leakage compensation, according to the manual.
  • Electrical supply: Match the site voltage to the analyzer nameplate. The pressurized hazardous-location variant is configured for a specific rated input voltage rather than a wide-range supply.
  • Mounting and lifting: The analyzer weighs 55 kg. Use suitable, rated lifting equipment, and ensure the mounting surface is stable and able to support the unit.
  • Environment and connections: Follow the applicable requirements for cable glands, conduit, protective gas supply and enclosure installation. Protect cable glands and piping where mechanical damage is a concern.
  • Alarm integration: Connect purge-controller fault outputs as required by the site’s safety and control design.

Some configurations have additional requirements. For example, the manual specifies a minimum 280 L/min compressed-air flow to cool the top compartment when the analyzer is fitted with the identified Elmess gas cell heater. Confirm variant-specific instructions before commissioning.

Purging, startup and shutdown are safety-critical

Purging is a defined safety step, not an optional maintenance convenience. The manual requires a minimum purge of 2 minutes 30 seconds at a flow rate of at least 280 L/min and a pressure of 1.5 ± 0.5 bar for specified purging procedures, including after opening the enclosure before power is restored. Follow the exact procedure in the analyzer documentation and the site’s safe-work practices; do not infer purge conditions from a different operating step.

Before opening covers, isolate and lock out electrical power. Sample gas must be vented, and the gas system must be purged as directed to prevent hazards during maintenance. The manual also calls for the analyzer and sample-return system to run for five minutes so gas in the analyzer can be returned to the exhaust. When shutting down, lock out the gas-handling system and isolate calibration gas and compressed air as required by the procedure.

During pre-purge, the manual requires inputs and outputs connected to external equipment to be shut off. It also warns against operating the analyzer with doors or covers open, opening it when an explosive atmosphere may be present, or leaving the protective gas supply valve closed while hazardous conditions remain. These steps require trained, authorized personnel who understand the relevant manuals and site procedures.

Maintenance requires trained personnel

The analyzer can contain hot surfaces, pressurized gas and components exposed to sample residues. Some parts may reach 160 °C. The manual specifies allowing the unit to cool for at least two hours before general maintenance and at least 12 hours before work on or near the insulated analysis cell. Use appropriate personal protective equipment, and handle used gas-handling components cautiously because particulate residue from the sample may be present.

Use only replacement parts authorized and approved for hazardous-area use. Certain optical repairs and alignments require specialized test equipment and procedures; the manual directs repairs to Emerson when the required replacement procedure is not provided. After maintenance, confirm that tools and loose items are removed, compartments are clean, vents are unobstructed and the system is safe to return to operation.

Practical implications for plant teams

The Rosemount CT5100(Ex) brings continuous, multi-gas laser measurement to process applications, but its use depends on more than the sensing principle. Engineering teams should confirm the analyzer variant and certification conditions, provide suitable utilities, integrate purge alarms, and establish documented startup, shutdown and maintenance procedures. Above all, installation and service should be performed by qualified personnel using the complete product documentation and applicable site rules. Treating these requirements as part of analyzer design and operations planning helps protect personnel, equipment and process safety.

Access Official Technical PDF

About The Author