Access Official Technical PDF

Share Summary:LinkedInEmail

Timekeeping is a small but important function in many industrial and embedded systems. Controllers may need to maintain a calendar, schedule an event, generate an interrupt or preserve time through a change in operating conditions. The RX-8571 real-time clock (RTC) provides these functions in a low-power device with an I2C-Bus interface, built-in 32.768 kHz crystal unit and frequency-output options. For automation engineers and system integrators, its value lies in combining several timing functions while keeping the host interface straightforward.

RX-8571 real-time clock functions at a glance

The RX-8571 family is offered in SA, NB and LC package versions. Its core functions include time and calendar keeping, an alarm, a programmable timer, a controlled frequency output and 128 bits of SRAM organized as 16 words of 8 bits. This onboard RAM can hold small amounts of user data; it is not a replacement for larger system memory.

The device communicates over an I2C-Bus interface rated for operation up to 400 kHz. Its integrated crystal unit is specified at 32.768 kHz, a common reference frequency for clock and timing circuits. A frequency-adjustment function is also included. Output selection supports 32.768 kHz, 1024 kHz or 1 Hz, with output enable controlled either through the FOE hardware pin or software selection bits.

Power and operating conditions

Supply planning is central when selecting an RTC for an embedded controller, remote instrument or other power-conscious design. The RX-8571 operating supply range is 1.6 V to 5.5 V. Its timekeeping supply range extends from 1.3 V to 5.5 V, allowing the clock-keeping function to remain supplied at a lower voltage than the normal operating minimum. These are distinct limits and should be considered separately when designing the power architecture.

The specified operating temperature range is -40°C to +85°C. Typical current consumption is listed as 220 nA for the LC version and 200 nA for the SA/NB versions under the stated conditions: 3 V supply, 25°C, with the frequency output and interrupt output off. A maximum of 550 nA is listed across -40°C to +85°C for the specified measurement conditions. Actual system current will depend on configuration and operating conditions, so engineers should use the detailed device documentation when estimating battery life or total power consumption.

Using alarms, interrupts and the timer

The alarm function can be configured using combinations of calendar and time fields, including date, hour and minute. When an alarm event occurs, the device records the event in its flag and asserts the /IRQ output. The interrupt provides a way for a host controller to respond to a scheduled event without continuously polling the RTC.

A separate timer function supports programmed intervals from 244 microseconds to 65,535 clock units, as specified for the device. On a timer event, a timer flag is set and the /IRQ output can signal the host. This gives a design a hardware-based timing option for periodic or delayed events, while keeping event handling under the control of the main processor.

During implementation, firmware should account for the relevant status flags and interrupt configuration. The RTC provides the event indication; the host still needs to read and handle the appropriate state as part of its application logic.

Design considerations for integration

Choose the appropriate output and interface strategy

Not every application needs a continuous frequency output. Where it is required, the selected 32.768 kHz, 1024 kHz or 1 Hz output can be enabled or disabled through hardware or software control. Where it is not needed, disabling the output is consistent with the stated low-current measurement conditions. The I2C connection provides access to the RTC’s functions, while /IRQ offers a dedicated event signal.

Account for assembly and package details

The SA, NB and LC variants use different package formats and pin arrangements. PCB footprints and routing should therefore be based on the exact selected version rather than treating the family packages as interchangeable. The device documentation also warns against applying adhesive or glue to the back of a mounted component in a way that allows material to enter between the package and the glass. Such material can stress or damage the glass and may stop the crystal oscillating. Assembly processes should prevent this exposure.

Verify the current specification

Component documentation may change, and the manufacturer advises confirming the latest information before production design. Engineers should review the current datasheet and application guidance for the selected package, electrical limits, timing behavior and any application-specific requirements.

Conclusion

The RX-8571 real-time clock brings calendar timekeeping, alarm and timer interrupts, selectable frequency outputs and small onboard SRAM into an I2C-connected device. Its low typical current, broad operating supply range and extended timekeeping voltage range can support a range of embedded automation designs. Successful integration depends on matching the package to the PCB, configuring outputs and interrupts for the application, and observing the crystal-package assembly precautions. These checks help ensure the RTC’s timing functions fit cleanly into the wider control system.

Access Official Technical PDF

About The Author