Series-connected power devices offer a way to address a persistent challenge in automotive power electronics: achieving the required voltage capability without relying on a single, costly high-voltage semiconductor. The approach uses multiple lower-voltage-rated devices controlled together, but introduces a critical design concern: ensuring that voltage is shared appropriately during switching. Combining series connection with soft switching can help manage that concern while supporting efficiency and cost objectives.
These trade-offs matter across electrified vehicle systems, from traction inverters to isolated DC–DC converters. Engineers must consider not only semiconductor performance, but also switching losses, passive-component size, thermal management and the stability of each device under transient conditions.
Automotive power electronics has competing priorities
Electric and hybrid vehicles use power conversion systems with different power levels and requirements. A traction drive has a direct effect on vehicle energy use, while accessory power systems place greater emphasis on compactness and cost. There is no single semiconductor choice that suits every converter or operating condition.
Silicon carbide (SiC) and gallium nitride (GaN) devices are wide-bandgap semiconductors that can offer lower conduction and switching losses than conventional silicon devices. Their faster switching can also enable higher switching frequencies, which may reduce the size of passive components such as inductors, capacitors and transformers. SiC devices are discussed for high-power applications such as traction inverters, while GaN devices can suit high-frequency isolated DC–DC conversion.
However, the source review identifies device cost as a barrier to broad automotive adoption. This creates interest in using lower-voltage-rated devices in configurations that can meet the voltage requirements of a power conversion system.
How series-connected power devices work
In a series-connected arrangement, two or more semiconductor switches operate together as a single switching element. Using several lower-voltage devices can provide the required overall voltage capability. The review compares such arrangements with single higher-voltage devices and notes potential advantages in total on-resistance. Actual converter performance also depends on factors such as device parasitics and body-diode behavior, so conduction resistance alone does not determine the result.
The main engineering challenge is voltage imbalance. Ideally, devices in a series stack share the applied voltage evenly. In practice, differences in switching timing and device characteristics can make one device experience more voltage than another during a transient. Unequal sharing can place excessive electrical stress on an individual switch, making voltage balance an important part of the design rather than an assumption.
Why timing and device variation matter
During turn-off, even a small difference in timing can affect how voltage rises across each device. Differences in voltage-transition rates can contribute to imbalance even when the gate signals are synchronized. Device threshold-voltage variation is identified in the review as an influential factor, alongside timing differences and parasitic elements.
One possible response in a hard-switched converter is to reduce the rate of voltage transition. But slowing the transition can compromise efficiency or system size. Active balancing approaches can instead adjust device timing or gate-drive behavior, though these methods may add control complexity or cost.
Soft switching can support voltage balance
Soft switching shapes voltage and current during switching transitions, commonly using resonant inductors and capacitors. In zero-voltage switching (ZVS), a device turns on when the voltage across it is zero. In zero-current switching (ZCS), turn-on occurs when device current is zero. Some converter operations combine both conditions.
By reducing voltage and current overlap during switching, soft-switching techniques can reduce switching stress and losses. They can also moderate the voltage transition that contributes to imbalance in a series stack. This does not remove the need to assess device variation or verify voltage sharing; rather, it gives the designer another circuit-level tool for managing the transient.
Soft-switching circuits require additional components and careful design. In a three-phase motor-drive inverter, for example, an auxiliary resonant commutated pole (ARCP) topology uses auxiliary switches and resonant components to shape transitions. The reviewed work describes ZVS turn-off for the main switch and zero-current transitions for auxiliary switches. It also discusses soft switching as a way to mitigate false turn-on associated with recovery current in bridge-type converters.
Why LLC converters are relevant
LLC resonant converters are used in isolated DC–DC applications, including conversion between a high-voltage vehicle battery and a 12 V auxiliary battery. Their resonant operation enables soft-switching transitions. In the reviewed analysis, the excitation current charges device parasitic capacitance during dead time, producing a slower drain–source voltage transition at turn-off.
That behavior can help limit voltage imbalance in series-connected devices without relying on the same kind of transition slowing that would be imposed on a hard-switched converter. The review also indicates that transformer excitation inductance and the resulting excitation current are relevant design parameters: selecting a larger excitation inductance can help suppress imbalance in the evaluated LLC configuration.
Design implications for engineers and integrators
For teams evaluating series-connected switches, the practical lesson is to treat device voltage sharing as a system-level design and validation task. Key considerations include:
- Characterize device variation: Threshold voltage, switching behavior and parasitic elements can affect transient voltage distribution.
- Coordinate gate-drive timing: Small turn-off delays can contribute to imbalance, even when devices are intended to switch together.
- Choose the switching method deliberately: Soft switching may help manage switching stress and voltage transitions, but adds circuit components and design requirements.
- Evaluate the converter as a whole: Conduction and switching losses, passive components, thermal design and control complexity all affect the system trade-off.
- Verify voltage sharing: Simulation and experimental testing can reveal differences between idealized assumptions and real device behavior.
Conclusion
Series-connected power devices can help make lower-voltage-rated semiconductors relevant to automotive converters where cost and efficiency are important. Their use depends on controlling voltage imbalance caused by switching delays, device variation and circuit parasitics. Soft-switching topologies, including LLC converters, provide a potential way to moderate switching transitions and support voltage balance, but they do not eliminate the need for careful design and validation. For automotive power-electronics teams, the strongest approach is to assess semiconductor choice, switching strategy, gate drive and converter parameters together.