SF6 emissions are associated with electrical equipment, but they can also arise from a range of less familiar products and processes. For industrial operators, system integrators and inventory teams, the challenge is often not identifying a single major source, but locating scattered uses across equipment, facilities and product lifecycles. A sound inventory begins by understanding where the gases are used, how they are contained and when they may be released.
The IPCC’s 2019 refinement to its greenhouse gas inventory guidance describes methods for estimating emissions of sulfur hexafluoride (SF6) and perfluorocarbons (PFCs) from these other applications. The same principles are useful for technical decision-makers assessing emissions sources: map applications, gather activity data, and choose a calculation method that reflects the quality of information available.
Where SF6 and PFCs are used beyond electrical equipment
This category covers applications that are not addressed under electrical equipment, semiconductor manufacturing, metal production or production of the gases themselves. Examples include SF6 in airborne radar systems and particle accelerators, PFC heat-transfer fluids in specialized electronics, and fluorinated compounds used in products or manufacturing processes.
Other applications described in the guidance include:
- SF6 in university, research, industrial and medical particle accelerators.
- SF6 or PFCs used in products such as sound-proof glazing, tires and sports footwear.
- PFC heat-transfer fluids in commercial and consumer electronic equipment.
- PFCs in some cosmetic and medical applications.
- Fluorinated compounds used to waterproof electronic circuits or treat textiles, carpets, leather and paper.
- SF6 and PFCs used as tracers, in leak detection or in other specialized applications.
The emissions profile depends on the application. A gas in a closed system may remain contained during normal operation, with releases occurring mainly during servicing, manufacturing or disposal. In other uses, the material may be emitted within a year of purchase. This timing matters: estimates based only on annual gas purchases can misrepresent emissions when a product stores gas for much of its service life.
Choosing an SF6 emissions estimation method
The guidance recommends using consumption information from gas users or collecting import, export and consumption data from producers and distributors. Where possible, consumption should be divided by application so that use in accelerators, for example, is not blended with use in unrelated products.
Methods are organized into tiers, ranging from broad estimates to detailed equipment-level accounting. The appropriate choice depends on the importance of the source and the data available:
- Country-level estimates use counts of equipment and default factors. These can be useful when individual equipment charges or user records are unavailable, but are described as rough approaches.
- Emission-factor methods apply a default or locally developed factor to the amount of gas held in equipment or used in a process.
- Mass-balance methods use records of gas acquired, stored, transferred, recycled, destroyed or added to equipment. These provide a more detailed estimate when reliable records are available.
For SF6 in Airborne Warning and Control System (AWACS) aircraft, the guidance gives a default estimate of 740 kg per plane per year, with an uncertainty of ±100 kg. It also notes that emissions vary with flight activity and leakage. Where detailed records exist, a mass balance can instead account for changes in stored SF6, purchases, transfers and changes in the fleet’s total equipment charge.
Particle accelerators: account for equipment type and charge
Accelerators use SF6 as an insulating gas, but charges and emission factors vary considerably by application. University and research systems may contain widely differing quantities, and losses can occur during maintenance, gas recovery and transfer, through pressure-relief events or through leaks. The guidance provides a default annual emission factor of 7 percent of the total SF6 charge for university and research accelerators.
Industrial and medical accelerators require separate factors. The inventory method should distinguish equipment by process type rather than applying one rate to every accelerator. For example, the guidance lists different charge factors for high-voltage industrial, low-voltage industrial and radiotherapy equipment, as well as different emission factors. When equipment-level charge and gas-handling records are available, a user-level mass balance can replace broad defaults.
Product lifetimes change when emissions occur
For products that retain gas during use, emissions may be spread across assembly, operation and disposal. In sound-proof double-glazed windows, the guidance assumes that about one-third of the SF6 used for filling is released during assembly. It also provides a default annual leakage rate of 1 percent of the gas capacity in existing windows. Disposal estimates depend on the remaining gas and the recovery factor; where country-specific information is unavailable, the guidance assumes a recovery factor of zero.
Other products have different delays. For certain adiabatic applications, including tires and sports shoe soles, emissions are treated as occurring three years after sales. By contrast, some medical or tracer applications are considered prompt-emission sources. Their estimates should reflect the timing of both sales and releases rather than treating all purchased gas as emitted immediately.
Emerging and difficult-to-quantify sources
The guidance provides emission factors for three gases associated with waterproofing electronic circuits using plasma processes: CF4, C2F6 and CHF3. To estimate emissions, apply each gas’s factor to the number of circuit boards processed. The text also identifies fluorinated treatments in textile, carpet, leather and paper production as a potential source, but notes that representative default emission factors were not available in the 2019 refinement. It therefore recommends working with equipment manufacturers and process users to measure equipment-, process- or site-specific factors.
This distinction is important for inventory quality. A source may be relevant even when a standardized calculation factor is not yet available. In that situation, documented measurement and collaboration with users can help establish a defensible estimate, while clearly recording assumptions and data limitations.
Practical implications for technical teams
For facilities and organizations that use SF6 or PFCs, the first step is to identify applications and responsible equipment owners. Useful records may include gas purchases, cylinder inventories, servicing and recovery logs, equipment charges, transfers, retirements and product throughput. These records support both emissions accounting and a clearer understanding of where losses may occur.
SF6 emissions from other products are difficult to estimate with a single universal factor because applications differ in containment, service life and release timing. The practical approach is to classify uses, choose a method suited to available data, and improve the estimate as equipment-level information becomes accessible. For plant managers and technical decision-makers, better records make inventories more transparent and help focus attention on the lifecycle stages where emissions are most likely to occur.