Access Official Technical PDF

Share Summary:LinkedInEmail

For engineers and technical decision-makers assessing photovoltaic systems, the Shockley-Queisser limit is a useful benchmark—but only when its assumptions are understood. It describes the theoretical performance of an ideal single-junction solar cell under a defined set of conditions. A real device falls short for specific optical, thermal, and electrical reasons, so comparing efficiency figures alone does not show where the differences arise.

The model provides a framework for separating those losses. Its practical value lies not just in the headline efficiency limit, but in the figures of merit that indicate how closely a completed cell approaches the model in different aspects of operation.

What the Shockley-Queisser model describes

Introduced by William Shockley and Hans Queisser in 1961, the model applies detailed balance to photovoltaic energy conversion. In simplified terms, it accounts for the balance between light absorbed by a semiconductor and light emitted as the cell operates. The absorber has a valence band and a conduction band separated by a band gap, Eg. A photon with enough energy can create an electron-hole pair; the carriers may then be collected as electrical current or recombine.

The conversion process has three stages:

  • Optical absorption: A photon creates an electron-hole pair.
  • Thermalization: Carriers lose energy above the band gap to the material’s lattice.
  • Electrical collection or recombination: Carriers reach separate contacts and contribute to current, or recombine and may emit a photon.

Each stage involves energy losses. Some photons pass through because their energy is below the band gap. Energy in excess of the band gap is lost during thermalization. Further losses arise from photon emission during recombination and from the difference between carrier energy and the electrical work delivered at the contacts.

For the model’s ideal single-junction cell, the maximum efficiency depends on the band gap and the assumed solar spectrum and operating conditions. The often-cited value is about 30% for a 5800 K blackbody spectrum; the model gives about 33% for a terrestrial spectrum. These are conditional reference values, not a single universal ceiling applicable to every photovoltaic design or operating environment.

Five assumptions behind the benchmark

The model becomes meaningful as a reference only when its idealizations are made explicit. It assumes:

  1. Step-like absorption: Photons above the band-gap energy are absorbed, while photons below it pass through without interacting.
  2. One collected carrier pair per absorbed photon: Every absorbed photon generates exactly one electron-hole pair that can contribute to short-circuit current.
  3. Thermal equilibrium of carriers and cell: The carriers, cell, and ambient are at the same temperature; the standard model uses 300 K for the cell.
  4. Radiative recombination only: Electron-hole pairs recombine only by emitting photons. Other recombination pathways are excluded.
  5. Ideal contacts: Contacts selectively collect electrons or holes, with negligible resistance and no collection barriers.

These assumptions define the model’s boundaries. For example, the use of a pn-junction in the original work illustrates charge separation but does not make that specific junction architecture a requirement of the model.

How real solar cells depart from the Shockley-Queisser limit

Optical losses reduce usable current

Real absorbers do not have perfectly sharp absorption edges. Structural disorder can create band tails, and finite thickness or absorption coefficients can allow some above-band-gap light to escape. Parasitic absorption in contact layers or by free carriers can also reduce the number of useful electron-hole pairs. These effects lower short-circuit current relative to the ideal value.

External photovoltaic quantum efficiency, or the probability that an incident photon produces a collected carrier pair, helps characterize this behavior across photon energies. Two useful comparisons are the measured short-circuit current relative to the model’s value, FSC, and the model’s radiative emission current relative to the real device’s radiative emission current, Fem. Both are at or below unity when optical assumptions are not fully met.

Temperature and recombination affect voltage

Outdoor modules often operate above the 300 K reference temperature. Because recombination currents are thermally activated, higher cell temperature primarily reduces open-circuit voltage. Temperature effects therefore matter when translating a laboratory reference into expectations for operation, though the precise impact depends on the technology and location.

In real cells, non-radiative recombination in the absorber or at interfaces is another major departure from the model. It increases recombination losses and reduces open-circuit voltage. External luminescence quantum efficiency, Qelum, compares radiative recombination with total recombination and provides a measure of this loss. The model’s relationship between absorption and emission also means that optical performance and voltage cannot always be assessed independently.

Electrical resistance lowers fill factor

Series resistance, finite parallel resistance, and limited carrier transport alter the current-voltage curve. Their effect is often expressed through the fill factor: the maximum power a cell delivers divided by the product of short-circuit current and open-circuit voltage. A resistance-related fill-factor metric compares the real fill factor with the ideal-diode fill factor expected at the cell’s measured open-circuit voltage.

Use a set of metrics, not one efficiency comparison

A single efficiency ratio cannot explain whether a device is limited by absorption, recombination, temperature, or charge collection. A more diagnostic assessment considers several measurements together: short-circuit current relative to the reference, optical emission behavior, external luminescence quantum efficiency, and fill-factor losses. The model’s temperature assumption should also be kept in view when comparing cells measured or operated under different conditions.

These figures of merit should be determined on complete devices where possible. Measurements on an absorber alone may not capture contact selectivity, resistance, or the trade-offs between light emission and carrier collection. Improving one metric in isolation can also come at the expense of another; the goal is to understand and manage the combined losses.

Practical takeaway

The Shockley-Queisser limit is most useful as a structured reference for single-junction photovoltaic performance—not as a stand-alone pass/fail threshold. For engineering evaluations, connect efficiency to the underlying current, voltage, recombination, temperature, and fill-factor behavior. That approach makes comparisons more informative and helps identify which device losses merit attention, while keeping conclusions within the assumptions and operating conditions of the model.

Access Official Technical PDF

About The Author