Access Official Technical PDF

Share Summary:LinkedInEmail

SiC MOSFET power modules are attractive for solar inverter designs that target high switching frequencies and efficiency. But using these devices effectively requires attention to their switching behavior, not just their potential advantages. In an active neutral point clamped (ANPC) inverter, fast voltage transitions can contribute to parasitic turn-on of a device that is meant to remain off, creating cross-conduction. Understanding how this happens helps engineers assess module behavior and identify what must be validated in the inverter design.

SiC MOSFET power modules in an ANPC solar inverter

The examined application is a 1500 V string inverter based on an ANPC power module. The three-level topology combines silicon IGBTs and SiC MOSFETs: four IGBTs operate in synchronization with the grid frequency, while two MOSFETs perform fast switching. The inverter phase also includes DC-link capacitors and an AC-side choke. The target switching frequency is up to 64 kHz.

This arrangement illustrates how different semiconductor devices can serve distinct roles within one power stage. The SiC MOSFETs handle fast switching, while the IGBTs operate at grid frequency. Assessing the MOSFETs therefore involves looking closely at the events surrounding turn-on and turn-off, including what happens in the other device in the commutation pair.

What double-pulse testing revealed

To examine switching behavior, SiC MOSFETs from multiple suppliers were evaluated in a hard-switching, totem-pole half-bridge configuration. Measurements used a double-pulse characterization test station. The same direct copper bonded (DCB) layout was used across the tests, helping keep layout-related parasitic inductance consistent so that the MOSFET type was the variable under investigation.

In the measurement sequence, the low-side MOSFET was switched on long enough to build current, then switched off briefly. During that interval, current commutated through the body diode of the high-side MOSFET. Turning the low-side device on again allowed the switching waveforms and energies of the MOSFET and diode to be assessed.

The observed low-side turn-on waveform included a sharp drain-current spike followed by ringing in both drain current and gate voltage. This behavior indicated parasitic turn-on of the opposite device, also known as cross-conduction or shoot-through. The result shows why it is important to evaluate the complete commutation event: the switching behavior of one MOSFET can affect the device paired with it.

How parasitic turn-on can occur

Before the low-side MOSFET turns on, current is flowing through the high-side MOSFET’s body diode. As the low-side device begins conducting, current transfers from that diode to the low-side channel. The high-side diode then blocks, and the midpoint voltage moves from the DC-positive rail toward zero with a high rate of change, or dv/dt.

A SiC MOSFET has intrinsic capacitances between its drain, gate and source. In particular, the Miller capacitance, Cgd, couples the drain and gate; Cgs is between gate and source; and Cds is between drain and source. During the rapid voltage transition, current associated with these capacitances can raise the voltage across Cgs. If the gate voltage reaches the device’s turn-on threshold, the nominally off MOSFET can begin conducting. This explains the mechanism behind the observed cross-conduction.

For inverter designers, the practical point is that fast switching transitions interact with the device’s gate and power circuit. A waveform that appears to be a turn-on event in one switch may also produce a significant gate-voltage response in its counterpart. Looking only at the commanded gate signal or at steady-state operation may not reveal the full interaction.

What engineers should include in validation

Switching characterization should capture the relevant waveforms during commutation, including drain current, drain-source voltage and gate-source voltage. The double-pulse method provides a controlled way to examine these events and compare device behavior. Consistent test conditions and layout are also important: using the same DCB layout in comparative measurements helps separate device-related differences from changes in parasitic inductance.

In a project design review, engineers and integrators can use this mechanism to guide questions such as:

  • Does the opposite MOSFET’s gate-source voltage remain below its turn-on threshold during the commutation transition?
  • Do measured current and gate-voltage waveforms show spikes or ringing that require further investigation?
  • Are test conditions and circuit layout representative enough to support meaningful comparisons?
  • Have both devices in the commutation pair been assessed, rather than only the commanded switch?

These checks do not replace validation in the application circuit. They help teams understand what the switching event reveals and where additional evaluation may be needed before relying on a particular device and module arrangement.

Balancing switching performance with design scrutiny

SiC MOSFETs can be part of high-frequency ANPC solar inverter designs, but their fast switching makes parasitic behavior a central consideration. In the examined half-bridge measurements, a rapid midpoint-voltage transition was associated with a gate-voltage rise in the opposite device and a waveform consistent with cross-conduction. The capacitance relationships explain how that response can occur.

For plant operators and technical decision-makers, the implication is straightforward: selecting a power module is only one part of achieving predictable inverter operation. Engineering teams should also characterize commutation behavior under controlled conditions and verify the interaction between paired devices. Careful attention to these switching details helps teams assess whether a SiC MOSFET-based module is suitable for the intended inverter design.

Access Official Technical PDF

About The Author