A simple AM transmitter is a useful case study in how circuit architecture shapes the behaviour of an RF system. Designs can range from a single valve and a handful of components to a frequency-synthesised transmitter with microcontroller control. For automation engineers and technical teams, the comparison illustrates familiar design priorities: managing power and signal paths, maintaining frequency stability, controlling unwanted outputs and testing the complete system rather than relying on a schematic alone.
The examples discussed here were developed for radio hobby and demonstration use, not industrial communications. Their value is in the engineering principles they make visible: amplitude modulation, oscillator control, filtering, impedance matching and measurement.
Simple AM transmitter design: two different approaches
A basic AM transmitter combines an RF carrier with an audio signal so that the carrier’s amplitude varies in response to the audio. The receiver can then recover that programme by detecting the changes in carrier amplitude. How the carrier is generated and how the audio is applied determine much of the transmitter’s complexity and performance.
One competition entry used a 117L7 valve, a dual-function tube containing a diode section and a beam pentode. The builder adapted a circuit originally described for 120 V mains by adding a transformer with a 230 V primary and two 117 V secondary windings. An oscillator coil, assembled components and an antenna salvaged from a transistor radio completed the project. A CD player supplied the audio, and a Bell AM radio served as the receiver.
After a small adjustment to the oscillator coil’s slug, the programme could be heard on a quiet part of the receiver dial. The result demonstrated how few components can produce a working AM link, while also revealing the limits of repurposing a valve that was not designed for this application. The reported fidelity was passable rather than exceptional.
Using a PLL for frequency stability
A more elaborate design used a phase-locked loop (PLL), a voltage-controlled oscillator (VCO), a crystal reference and a microcontroller. Instead of relying on a free-running oscillator alone, the PLL continually compares divided versions of the reference and VCO signals. Its phase detector produces a correction signal, which passes through a low-pass loop filter and adjusts the VCO through a varicap diode.
When the loop locks, the VCO frequency is related to the crystal frequency by the selected divider values. A microcontroller programs those values, displays the selected frequency and allows the operator to tune with up and down switches. The design also stores the selected setting in EEPROM so it can be restored after power is removed.
In the documented example, a 7.488 MHz crystal reference and divider settings produce a 9 kHz reference at the phase detector. The VCO is set to 8.496 MHz, and mixing it with the crystal frequency produces a 1.008 MHz carrier. This illustrates how a frequency synthesizer can create a selected output from a stable reference through division and mixing.
Modulation, filtering and unwanted signals
Generating the carrier is only part of the task. The PLL transmitter routes line-level audio through an automatic level control (ALC) circuit and amplifier before it reaches the modulator. The ALC helps control audio level, while an indicator shows when sufficient audio is present. These functions address a practical issue in AM: the audio signal must be applied in a controlled way to produce usable modulation.
Filtering is equally important. Mixing frequencies creates unwanted products, and a transmitter can also produce harmonics. The PLL design uses filtering after the mixer and after the modulator to reduce unwanted frequency components. It also mutes the RF output when the synthesizer is not locked, preventing transmission while the carrier is outside its intended state.
Testing revealed that measured results depend on the measurement setup. The builder observed unexpected spurious signals when checking the output with a receiver and attenuator, despite a different appearance on a spectrum analyser. Further investigation pointed to the crystal oscillator module; adding an RC filter at the relevant transistor stage brought the measured spurious signals below -60 dBc. The account is a reminder to verify suspicious readings with suitable instruments and consider whether the test equipment itself is affecting the result.
RF matching and system-level testing
The antenna is part of the RF system, not just an accessory. The PLL transmitter included a matching network and an adjustable loading coil. To tune the antenna, the builder used a simple crystal-set detector with a meter and adjusted the loading capacitor for a peak reading. The stated aim was to find maximum antenna current, rather than assume that a particular physical antenna arrangement would be correctly tuned.
On-air testing also exposed an interaction that was not apparent during circuit development: the RF affected the CD player, which stopped reading the disc shortly after transmission began. Moving the player and avoiding a peak in antenna tuning improved the result. This highlights the importance of testing the complete setup, including audio sources, cables, enclosure and antenna placement.
Practical lessons for engineers
- Match architecture to the requirement. A valve circuit offers simplicity; a PLL-based design adds programmable control and a crystal-referenced frequency.
- Plan for unwanted outputs. Mixing, harmonics and oscillator leakage make filtering and measurement part of the design process.
- Test the loop and the whole system. PLL stability, RF coupling and antenna tuning can only be assessed by checking the assembled transmitter in operation.
- Separate observed results from assumptions. Instrument readings, receiver checks and system behaviour provide different evidence and may need to be cross-checked.
Conclusion
These simple AM transmitter projects show a progression from a minimal valve circuit to a controlled RF system built around a PLL, microcontroller and tuned output. The more advanced design demands additional work in frequency planning, loop stability, filtering, matching and troubleshooting, but it also provides greater control over tuning and lock behaviour. For engineers, the practical takeaway is that even a compact transmitter must be treated as a complete signal chain: carrier generation, modulation, output conditioning, antenna interface and test setup all influence the result.