Access Official Technical PDF

Share Summary:LinkedInEmail

Simultaneous switching noise (SSN) is a power-integrity concern in mixed-signal integrated circuits. When multiple digital gates switch, transient current can produce voltage fluctuations on the supply and ground networks. Those disturbances may couple through a shared substrate or power distribution paths and affect nearby analog circuitry. A 45 nm circuit study examines a low-noise approach using an inverter-based equivalent model, then applies the design to a Gate Diffusion Input (GDI) half adder and a 4-bit arithmetic logic unit (ALU).

For engineers assessing IC power integrity, the work highlights two connected design questions: how parasitic elements shape switching noise, and how logic implementation choices affect transistor count and power utilization. Its reported results are simulation-based and relate to the circuit configurations and conditions described below.

Why simultaneous switching noise matters in mixed-signal VLSI

As device dimensions shrink and circuit density increases, digital and analog functions are more likely to share a die. Digital switching produces current peaks; those currents interact with parasitic impedance in the supply network, creating voltage deviations on VDD and ground. This disturbance is commonly described as switching noise or ground bounce.

In a mixed-signal design, the issue is not confined to the digital block that generates the switching activity. Noise can travel through shared substrate and supply paths, potentially degrading the behavior of analog circuits. The source study also identifies other contributors to IC noise, including process-related device variation, capacitive coupling between neighboring interconnects, charge sharing and charge leakage. Its analysis focuses specifically on switching noise.

Common mitigation approaches include decoupling capacitors, separate analog and digital supplies, guard rings, clock modulation and noise cancellation. The proposed work instead analyzes an equivalent circuit that represents the power-distribution parasitics with resistance, inductance and capacitance.

Modeling SSN with parasitic RLC elements

The equivalent circuit uses CMOS inverter gates and a ramp input to represent switching behavior. Resistance, inductance and capacitance model parasitic impedance in the supply network. The analysis considers how the number of simultaneously switching drivers, parasitic inductance and input transition rate influence the resulting voltage disturbance.

In the study’s mathematical treatment, the peak-noise relationship is expressed using a circuit-related quantity, H, defined as the product of the number of similar drivers (N), parasitic inductance (L) and input slew rate (sr). This framing makes the design implication clear: changing any of these three factors can affect the modeled SSN. The analysis also cautions that the peak noise may occur after the input transition has ended. Measuring only during the transition can therefore miss the maximum response under some damping conditions.

The model is evaluated in Tanner EDA with a 45 nm technology file and Spice simulation. The reported setup uses a ramp waveform, an 8 MHz frequency and a 5 V supply. The proposed circuit is compared with an existing equivalent-circuit design across specified RLC values.

Reported results for the equivalent circuit

For a resistance of 0.5 ohm, inductance of 100 pH and capacitance of 5 pF, the proposed model reports a peak noise of 140 µV, compared with 33 mV for the existing circuit. At 1 ohm, 100 pH and 5 pF, the reported values are 100 µV for the proposed circuit and 7.5 mV for the existing circuit. Both comparisons use an 8 MHz frequency.

These figures describe the simulated equivalent-circuit cases; they should not be treated as universal values for other layouts, process conditions or operating points. The study’s results are tied to its stated model and simulation setup. In practical design work, engineers would need to evaluate their own supply network, switching activity and parasitic extraction results.

Extending the approach to GDI logic

The study next applies the noise-reduction circuit to a half adder and a 4-bit ALU using GDI logic. A GDI cell has three inputs: a common gate input shared by NMOS and PMOS devices, plus separate inputs connected to the source or drain of each transistor. The authors use this logic style to implement functions with fewer transistors than the compared conventional designs.

For the half adder, the reported transistor count falls from 21 in the existing design to 11 in the proposed GDI design. Maximum power utilization is reported as 4.456427 mW and 2.951001 mW, respectively. The listed peak noise values are -10.083 dBVrms for the existing design and -10.077 dBVrms for the proposed design. These noise figures are close, so the reported half-adder comparison supports a reduction in transistor count and power utilization, but does not show a meaningful reduction in the listed peak-noise value.

For the 4-bit ALU, the comparison reports 910 transistors and 92.4 mW for the CMOS design, versus 657 transistors and 45.84 mW for the GDI design. The listed peak-noise values are 5 V and 2 V, respectively. These results indicate lower transistor count, power utilization and reported peak noise for the proposed ALU configuration in the study’s simulation.

Practical implications for circuit design

For system designers, the central lesson is that SSN should be evaluated as a transient power-distribution problem, not only as a logic-level issue. The number of active drivers, parasitic inductance and switching slew rate all feature in the study’s model. The timing of the measurement matters as well: a brief input transition does not guarantee that the largest noise excursion occurs within that transition.

Logic architecture is another consideration. The reported GDI implementations use fewer transistors, with lower simulated power utilization in the half-adder and ALU comparisons. However, the results are circuit- and setup-specific. They do not replace verification against the requirements and implementation details of a target IC.

Conclusion

The 45 nm study presents a parasitic RLC-based method for analyzing and reducing simultaneous switching noise, then evaluates the approach in GDI arithmetic circuits. Its equivalent-circuit simulations report substantially lower peak noise for the stated test cases, while the half-adder and ALU comparisons examine transistor count, power utilization and noise. The practical takeaway is to account for parasitics, switching activity and post-transition behavior during power-integrity analysis, and to validate any proposed circuit-level improvement under the conditions of the intended design.

Access Official Technical PDF

About The Author