Access Official Technical PDF

Share Summary:LinkedInEmail

A single-speaker OAE probe is a proposed way to simplify the hardware used for objective hearing screening. Conventional transient evoked otoacoustic emission (TEOAE) probes typically use one transducer to deliver an acoustic stimulus and a separate microphone to record the ear’s response. A prototype design explores whether one speaker can perform both tasks, potentially reducing the probe’s mechanical and assembly complexity. Early testing indicates feasibility, but also exposes performance limitations that matter when moving from a laboratory concept toward a usable screening device.

Why simplify otoacoustic emission screening?

Otoacoustic emissions (OAEs) are acoustic signals produced by active processes in the inner ear. In a TEOAE screening test, a brief stimulus—often a click—is delivered into the ear canal. The resulting response is recorded and analyzed. Because the test does not require the person being screened to provide feedback, it can be used with infants and young children as well as adults. Screening results generally indicate “pass” or “refer”; they are not a substitute for a full hearing diagnosis.

Access to screening can be limited by equipment cost, availability of trained personnel and the practical difficulty of reaching people outside established healthcare settings. A compact, easier-to-manufacture probe could help address some hardware barriers. The design described here targets a probe cost of about $10, compared with commercial probes priced at several hundred dollars. That figure is a proposed cost, not a demonstrated retail price or evidence of a finished, production-ready device.

How a single-speaker OAE probe works

The key design change is to use the speaker first to emit the click and then to record the much weaker acoustic response. In a conventional probe, separate acoustic channels connect the speaker and microphone to the ear canal. A single-transducer design needs only one channel, which can simplify the probe tip, component count, electrical connections and assembly.

The approach takes advantage of the time difference between the outgoing stimulus and the returning TEOAE. The prototype work used clicks of roughly 100 microseconds and recorded the response over a window typically lasting 20 milliseconds. Since the response arrives after the stimulus, the same transducer can, in principle, be used for both operations.

This simplification creates a central engineering trade-off: a speaker is substantially less sensitive for recording than a dedicated microphone. OAEs are weak signals, so the probe and measurement electronics must capture the response without allowing noise or residual speaker motion to overwhelm it.

Probe design and acoustic characterization

Five prototypes were built around different commercially available speakers. Their bodies were made using stereolithography 3D printing, with a similar overall design adjusted to fit each speaker. Each probe included an acoustic channel, a cap and wiring, with joints sealed to keep the probe body airtight. Replaceable commercial ear tips were used to interface with the ear canal.

The design requirements extended beyond selecting a transducer. A screening probe needs to deliver and record sound across relevant frequencies, form a suitable seal against the ear canal and limit interference from environmental sound. It also needs a replaceable tip and dimensions suitable for the intended user population. A simpler tip may make those mechanical goals easier to pursue, but acoustic performance still depends strongly on the probe’s geometry and materials.

Testing assessed the prototypes in both operating modes:

  • Speaker response: Measurements in an ear simulator examined how electrical drive produced sound pressure across frequency.
  • Settling behavior: Tests measured how much the speaker continued to vibrate after a short click. This residual “ringing” can interfere with the response that follows.
  • Recording sensitivity: A custom calibrator and reference microphone were used to characterize the electrical output produced when sound was applied to the probe.

The results varied substantially between prototypes. The CUI CDS-16098A showed the strongest overall recording performance among the evaluated probes in the frequency regions considered important for TEOAE, though its sensitivity declined above 4 kHz. Other designs showed issues such as insufficient low-frequency stimulation or excessive settling activity. These differences underline why replacing a microphone with a speaker cannot be treated as a simple component substitution.

Measurement electronics and signal processing

Because the recording signal was weak, the test system included a low-noise 50 dB preamplifier. The setup also had to manage simultaneous stimulus output and response input through the same transducer. A series resistor was used to increase the output impedance of the sound-card connection, balancing drive level against added noise. A digital band-pass filter limited the analyzed signal to 500 Hz–5 kHz.

Signal processing helped separate the OAE from stronger linear reflections, such as sound reflected within the ear canal. The click sequence used three equal-polarity clicks followed by a higher-amplitude, inverted-polarity click. Averaging the responses allows linear components to cancel while retaining the nonlinear TEOAE response.

To assess the result, the system divided successive click sequences between two buffers. Similarity between the buffers indicated a stable recording; their difference provided an estimate of noise. The study treated a signal-to-noise ratio (SNR) of 6 dB as sufficient to indicate an OAE under its measurement method.

What the feasibility study showed

The two selected prototypes were evaluated on four adults whose normal hearing had first been established using a commercial OAE screening device. Across 14 ear measurements, 10 reached the study’s “pass” criterion and four were classified as “refer” after the full measurement period. One ear could not be measured with the larger of the two probes because of its fit in the outer ear.

Some measurements reached the SNR threshold after repeated averaging; one example reached 6 dB after 400 click sequences, corresponding to about 23 seconds if testing stopped at that point. The authors noted that conventional microphone-based probes could complete measurements in mere seconds. The comparison makes clear that feasibility is not the same as equivalent screening speed or performance.

Tests in an ear simulator, where no biological OAE was present, produced low SNR and correlation values. This was a useful check that the system did not simply report a response in the absence of an OAE. However, the small adult study does not establish performance in newborns, children, varied ear anatomies or routine field conditions.

Practical implications

The single-speaker OAE probe demonstrates a path toward reducing the mechanical complexity of TEOAE screening hardware. Its one-channel design may support simpler assembly and probe-tip construction, while prototype characterization shows that some speaker choices are more suitable than others. At the same time, low recording sensitivity, settling behavior, fit and measurement duration remain important constraints.

For engineers and device developers, the next steps are not just to miniaturize the probe or select a low-cost speaker. They include systematically improving acoustic characteristics, validating the design across a wider range of users and developing a cost-effective measurement system. The work is an early feasibility result: promising as a design direction, but not yet evidence of a manufacturing-ready screening product.

Access Official Technical PDF

About The Author