Access Official Technical PDF

Share Summary:LinkedInEmail

An SMA rectifier diode is a compact component for converting alternating current to direct current and managing current paths in power electronics. The S1A–S1M family uses a surface-mount SMA (DO-214AC) package and offers a range of reverse-voltage ratings for general-purpose rectification in power supplies, inverters, converters, and freewheeling circuits. Selecting the right variant involves more than matching the circuit’s nominal voltage: engineers must also consider current, surge conditions, thermal behavior, and assembly requirements.

SMA rectifier diode family and voltage options

The S1 family includes seven device types, differentiated primarily by their maximum recurrent peak reverse voltage, or VRRM. Options range from 50 V for the S1A through 100 V, 200 V, 400 V, 600 V, and 800 V, up to 1000 V for the S1M. Their maximum DC blocking voltage matches the corresponding VRRM rating. Maximum RMS voltage ranges from 35 V to 700 V across the family.

All models have a maximum average forward rectified current, IF(AV), of 1.0 A. The specified maximum instantaneous forward voltage is 1.1 V at 1.0 A. These ratings provide a starting point for comparing variants, but they do not replace evaluation against the electrical and thermal conditions of the actual circuit.

When choosing a reverse-voltage rating, account for the blocking voltage the diode must withstand in normal operation and evaluate expected circuit conditions against the applicable maximum rating. The family’s listed voltage options allow designers to select among several ratings within the same package family. The appropriate choice depends on the application’s requirements and validated design margins.

Current, surge, and temperature considerations

Continuous and transient conditions both matter in rectifier selection. The datasheet specifies a 1.0 A average forward rectified current and a peak forward surge current of 40 A or 30 A, depending on the device group. The surge rating applies to an 8.3 ms single half-sine wave superimposed on rated load. It is a defined non-repetitive condition, not a substitute for checking repetitive current pulses or normal operating current.

Thermal design must account for how the diode is mounted and how heat moves from the junction into the board and surrounding environment. The datasheet provides forward-current derating curves and thermal characteristics, with thermal resistance values based on specified PCB copper pad areas. As mounting temperature rises, allowable average forward current is subject to derating. Use the published curves and the conditions stated with them when assessing a board layout; do not treat a current rating as independent of mounting and thermal conditions.

The operating junction and storage temperature range is -55 °C to +175 °C. The maximum junction temperature is 175 °C. These limits should be considered alongside expected ambient and board temperatures, dissipation, and the intended operating profile.

Electrical behavior and circuit application

The S1 series is intended for general-purpose rectification in power supplies, inverters, and converters, as well as use as a freewheeling diode. In a rectifier path, the diode conducts in the forward direction and blocks reverse voltage. In a freewheeling role, it provides a current path when an inductive load or switching circuit requires one. The specific circuit topology and operating conditions determine the required ratings.

Reverse leakage and switching behavior may also be relevant to the design. The datasheet lists maximum DC reverse-current values of 1.0 μA and 5.0 μA at 25 °C, depending on the listed rating, and 50 μA at 125 °C. It gives a typical reverse recovery time of 1.8 μs under the stated test conditions and a typical junction capacitance of 12 pF at 4.0 V and 1 MHz. These are specified characteristics to assess in context, rather than universal performance guarantees for every operating condition.

Package, placement, and ordering details

The SMA package has a low profile and is described as suitable for automated placement. Its single-device configuration and surface-mount terminals support integration into compact PCB assemblies. A color band identifies the cathode end, an important orientation check during placement and inspection.

For assembly planning, the terminals are matte-tin plated and specified as solderable according to J-STD-002 and JESD 22-B102. The parts meet MSL level 1 under J-STD-020, with a maximum peak temperature of 260 °C, and the E3, M3, HE3, and HM3 suffixes meet the JESD 201 class 2 whisker test. Package outline and recommended mounting-pad dimensions should be checked against the PCB footprint and manufacturing process.

Ordering suffixes distinguish material and qualification options. E3 denotes RoHS-compliant commercial grade, while M3 denotes halogen-free, RoHS-compliant commercial grade. HE3 and HM3 versions are AEC-Q101 qualified; HM3 is also identified as halogen-free and RoHS-compliant. Confirm the exact part number, revision code, and ordering information when specifying components, particularly for automotive designs.

Practical selection checklist

  • Choose a device whose reverse-voltage rating fits the circuit’s blocking-voltage requirements.
  • Verify average forward current and evaluate any surge against the stated waveform and non-repetitive conditions.
  • Use derating curves and thermal data that match the board mounting conditions.
  • Check leakage, recovery time, and junction capacitance where they affect circuit operation.
  • Confirm package footprint, cathode orientation, soldering requirements, and the required compliance or qualification suffix.

Conclusion

The S1A–S1M SMA rectifier diode family combines a 1.0 A average forward-current rating with reverse-voltage options from 50 V to 1000 V in a low-profile surface-mount package. For engineers and system integrators, the practical task is to match the specific device to voltage, current, surge, thermal, and assembly requirements—not to select by package or nominal current alone. Validate the chosen part under the conditions of the intended application and consult the current datasheet for complete ratings and ordering details.

Access Official Technical PDF

About The Author