Access Official Technical PDF

Share Summary:LinkedInEmail

In industrial and embedded systems, a two-wire communication bus can become less reliable as devices and trace lengths add capacitance. The resulting slow signal rise times may compromise communication timing. An SMBus accelerator addresses this challenge with active pull-up currents that help bus lines transition from LOW to HIGH without relying solely on stronger resistive pull-ups. The ISL88694 is a dual-channel example, compatible with SMBus and I2C operation at frequencies up to 100kHz.

Why bus capacitance affects communication

SMBus and I2C use a clock line and a data line, both of which are bidirectional. Their open-drain or open-collector outputs allow multiple devices to share the bus. Pull-up resistors connect the lines to a positive supply, so an unasserted line returns to HIGH; when a device pulls a line LOW, the bus can support the shared wired-AND behavior required for communication.

The drawback is that the pull-up must charge the capacitance on the bus when a device releases a line. Capacitance increases with connected device inputs and signal routing. With enough load, the line rises more slowly, potentially making communication unreliable or preventing the bus from meeting its timing requirements. Reducing the pull-up resistance can speed the transition, but it also increases current when the line is LOW.

How an SMBus accelerator improves rise time

The ISL88694 supplements the bus pull-up behavior with switched current sources on its two channels. Rather than applying the strongest pull-up continuously, it monitors each line as the voltage rises and boosts current during a valid rising transition.

Three stages of pull-up operation

  • Standby: When both bus lines are HIGH, the device reduces the pull-up current to 100µA to limit power consumption.
  • Active pull-up: When a line is LOW, an active pull-up current of 275µA is available to maintain the line’s behavior.
  • Boost: As a released line rises past the low threshold, VTRIPL, the accelerator applies a boost current. The typical boost current is 2.2mA, supporting a faster transition through the rising edge.

The boost switches off when the line reaches the high threshold, VTRIPH. The pull-up then returns to the active level; when both channels are HIGH, the device returns to standby current. Internal control prevents the active and boost pull-up sources from being activated during downward transitions.

For the ISL88694, VTRIPL is typically 0.75V, while VTRIPH is typically 0.5V below VDD. Because the high threshold is referenced to the supply through a bandgap-based circuit, the switching behavior is designed to remain consistent across the specified 2.7V to 5.5V supply range.

Noise filtering and signal integrity

A fast pull-up should respond to legitimate bus transitions, not every brief disturbance. The ISL88694 includes a noise filter on each channel. A rising input must exceed the low threshold by a sufficient voltage-time amount before the boost circuit activates. The electrical specifications give a typical noise-spike suppression value of 20V-ns. This filtering helps prevent short transients from triggering a boost response.

The device also provides 8kV human-body-model ESD protection on its SMBus pins. This is a specified protection level for those pins; it does not replace system-level decisions about wiring, grounding, or protection for the wider installation.

Design considerations for loaded SMBus and I2C lines

An accelerator can help when multiple device inputs or longer board traces contribute to bus capacitance. By adding temporary pull-up current during valid rising edges, it can support a larger bus load while avoiding the continuous low-state current associated with simply selecting a stronger resistor. The ISL88694 is specified for SMBus and I2C operation up to 100kHz, so the intended bus speed and electrical conditions should be checked against that limit.

During design review, engineers and system integrators should consider:

  • Bus topology and loading: Account for connected devices and trace routing when assessing line capacitance and rise time.
  • Supply compatibility: Keep the supply within the recommended 2.7V to 5.5V operating range.
  • Signal behavior: Confirm that the bus’s LOW and HIGH levels, pull-up arrangement, and timing are compatible with all connected devices.
  • Operating conditions: Check the device specifications and verify the implementation under the system’s actual operating conditions.

The ISL88694 is a compact, five-pin SOT-23 device with separate active pull-up connections for the two SMBus lines. Its specified operating temperature range is -40°C to +85°C. These details may matter when selecting a component for a control board or other embedded system, but they do not remove the need to validate the complete bus design.

Practical implications

For engineers troubleshooting unreliable communication on a capacitive two-wire bus, the key issue may be the time required for a released line to rise—not just the logic state itself. An SMBus accelerator such as the ISL88694 addresses that rise-time challenge by detecting valid transitions, applying temporary boost current, and reducing current when the bus is idle. The practical result is a way to support SMBus or I2C lines with added capacitance while retaining noise filtering and defined operating limits. Component selection should still be accompanied by a review of bus loading, supply voltage, frequency, and the requirements of every connected device.

Access Official Technical PDF

About The Author