Access Official Technical PDF

Share Summary:LinkedInEmail

A semiconductor SOIC-8 assembly change can affect more than the location where a component is built. It may also alter bill-of-material details, package marking and the information teams use to identify and trace devices. ON Semiconductor’s Final Product/Process Change Notification FPCN22191XE1 described qualification of its ON Semiconductor Philippines (OSPI) facility to assemble and test listed SOIC-8 products previously associated with Hana Microelectronics (HANA) or TongFu Microelectronics (TFME).

For industrial automation manufacturers, system integrators and maintenance teams, the central message was that the change expanded manufacturing capacity while keeping the affected products’ electrical characteristics unchanged. The notification also identified material differences between the former sources and OSPI, and introduced updated marking across all manufacturing sites. Those details matter when reviewing approved parts, incoming inspection procedures and component traceability.

What the SOIC-8 assembly change means

OSPI was qualified as an additional manufacturing location for assembly and test of the products listed in the notification. Following implementation, devices could be sourced from OSPI or from previously qualified manufacturing locations, depending on supply-chain capacity requirements. This is a dual-sourcing arrangement, not a statement that every unit will come from OSPI.

The notification gave a proposed first ship date of January 4, 2019, or earlier with customer approval. It stated that devices bearing date code W43 of 2018 or later could have been built at either the existing factory or OSPI. Customers were asked to raise written inquiries within 30 days of receiving the final notice if they did not accept the change.

To support testing at OSPI, consigned testers and handlers were transferred to the site. The same load boards, test programs and other necessary hardware were to be used for testing the affected products. The notice stated that electrical characteristics were not impacted and that electrical comparison reports were available on request.

Bill-of-material differences by previous source

The reported material changes depend on whether the previous assembly source was HANA or TFME. The notification listed no change to the leadframe or bond wire for the HANA-to-OSPI comparison. Die attach changed from Henkel QMI519 to Henkel SBP-8062T, while the mold compound changed from CEL8240HF10LYR and HENKEL GR828FC1 to EME G600. The JEDEC 2LI eCAT was unchanged.

For the TFME-to-OSPI comparison, the leadframe changed from Cu194 with matte Sn plating to Cu with a NiPdAu preplated finish. Die attach changed from Henkel Ablestik 8200T to Henkel SBP-8062T, and mold compound changed from Nitto MP8000CH4EN to EME G600. Bond wire was unchanged. The JEDEC 2LI eCAT changed from e3 to e4.

These distinctions are useful for engineering and quality teams assessing the notification against their existing approved-source records. The notice did not report a change to the eCAT for material from the existing source locations; OSPI material was identified as e4.

Marking and traceability updates

The notification also introduced a marking change for affected products at all manufacturing sites, not only OSPI. Line 1 identifies the product, while Line 2 carries a trace code. Its format identifies the assembly location, wafer lot ID and a two-digit date code; an “X” at the end of the line may serve as a wrap character when additional identification from Line 1 is needed.

The assembly-location code is “H” for HANA, “NF” for TFME and “P” for OSPI. A product marked with “P” as the assembly location therefore indicates OSPI assembly. The notification also said the box and reel label would show “ASSY LOC: PO” for product assembled at OSPI. Teams receiving components should use the package and shipping-label information together when confirming source and maintaining traceability.

Line 1 product identification was also specified for the affected devices, including LM2903M, LM2904M, LM358AM, LM358M, LM393AM, LM393M and LP2951CM, with corresponding “X” orderable variants listed in the notice. Because the printed identification may be split across lines, receiving and inspection instructions should reflect the stated marking format rather than relying only on a familiar full part-number string.

Practical review points for industrial teams

When processing a semiconductor manufacturing-site notification, engineering, quality, procurement and operations teams can use a coordinated review:

  • Confirm affected part numbers. Compare the notification’s listed devices with approved vendor and bill-of-material records.
  • Review source-specific material changes. Determine whether the existing approved source was HANA or TFME, since the listed leadframe, die-attach, mold-compound and eCAT details differ.
  • Update receiving and traceability procedures. Ensure staff can interpret the assembly-location code, trace code and reel or box label.
  • Assess validation requirements. The notification reported no electrical-characteristic impact and offered comparison reports on request; internal procedures determine what documentation or review is needed.
  • Coordinate supply decisions. Since sourcing could vary according to capacity, procurement and quality teams should align on how incoming lots from qualified sites are handled.

Conclusion

FPCN22191XE1 added OSPI as a qualified assembly and test source for selected SOIC-8 products, providing another manufacturing option while retaining the possibility of supply from previously qualified sites. The notification reported no electrical-characteristic impact, but it documented source-dependent bill-of-material changes and revised product marking across all sites. For industrial automation organizations, the practical response is to check affected part numbers, understand the material comparison relevant to the existing source, and make sure receiving, traceability and change-control records can accommodate the updated markings.

Access Official Technical PDF

About The Author