Solar cell technologies are evolving around a central engineering and commercial objective: reducing the levelized cost of electricity (LCOE). Higher conversion efficiency helps, but it is only part of the equation. Manufacturing cost, operating lifetime, energy yield and the cost of balancing or storing energy also influence the value of a photovoltaic (PV) system.
Understanding the main cell architectures—and the constraints each is designed to address—helps plant owners, integrators and technical decision-makers assess where PV development is heading. Crystalline silicon remains the dominant platform, while thin-film, perovskite and tandem designs offer different routes to improving performance and managing material and manufacturing trade-offs.
How a photovoltaic cell converts light into electricity
A solar cell is a semiconductor diode operating under illumination. When the cell absorbs light, it creates excess electrical carriers. The device must then separate and transport those carriers in different directions so they can contribute to current in an external circuit.
Several design factors determine how well this process works. The absorber must capture as much incoming light as possible, while the cell’s junction and electric field help separate carriers. Carrier diffusion or drift, electrical resistance in the base and emitter, and resistance at the contacts all affect how much usable current and power the cell can deliver. Efficiency is the cell’s electrical output divided by the incoming light power under defined measurement conditions.
Crystalline silicon: a mature platform still being refined
Crystalline-silicon technology has long accounted for the great majority of the PV market. Its production chain begins with silicon purification, followed by crystal growth, ingot shaping and wafer slicing. In the Czochralski process, purified silicon is melted and pulled into an ingot. The ingot is then cut into individual wafers using wire saws.
These steps create opportunities as well as costs. Producing high-purity polysilicon and growing ingots require energy, while wafer slicing removes material as kerf—the silicon lost during cutting. Thinner wafers and reductions in material use can therefore contribute to lower manufacturing costs, although cell and module design must still deliver the required performance and durability.
Cell architecture affects efficiency
The aluminum back-surface-field (Al-BSF) cell was a conventional industrial design. Its full-area aluminum contact on the rear can cause carrier recombination, limiting performance. Passivated emitter and rear contact (PERC) designs address this issue by adding rear-side dielectric passivation and openings for local contacts. The approach adds process steps, but improves rear-surface management and creates room for higher efficiency.
Further development has focused on reducing recombination at contacts, using n-type silicon and moving electrical contacts to the rear. A heterojunction back-contact design combines a crystalline-silicon absorber with amorphous-silicon layers at the rear, placing all contacts there and reducing front-side shading. Such structures can achieve high cell efficiency, but require more complex processing.
Module construction also matters. Cells are connected in series using conductive ribbons, assembled into strings, and combined with glass, encapsulant, a backsheet, a frame and a junction box. Improvements in cell performance need to be considered alongside material use and module design when evaluating overall system economics.
Thin-film photovoltaics: different absorbers, shared process logic
Thin-film PV typically uses a much thinner absorber than a silicon wafer cell. Manufacturing commonly deposits functional layers on a large glass or flexible substrate, with patterning and contact formation used to create the module. The broad process sequence can be similar across thin-film approaches, while absorber materials and their formation methods differ.
Important thin-film families include cadmium telluride (CdTe), copper indium gallium selenide (CIGS) and thin-film silicon. Each has its own research priorities. CIGS development includes work on absorber composition, surface passivation, thinner layers and scaling laboratory results to large-area manufacturing. Indium availability is also a consideration. For CdTe, priorities include module lifetime, absorber optimization, recycling and addressing concerns associated with cadmium toxicity. Thin-film silicon faces efficiency constraints, and amorphous silicon can degrade under prolonged illumination.
Perovskites and the challenge of commercial readiness
Perovskite refers to a crystal structure, rather than a single material. In photovoltaic research, perovskite absorbers commonly use an ABX3 structure, with combinations of organic cations and lead or tin, alongside halide anions such as iodine, bromine or chlorine. Their bandgap can be tuned through material composition, and cells can be made using solution processing or vapor deposition.
The attraction is a strong light-absorbing material that can work in a relatively thin layer. However, efficiency is not the only requirement for a viable PV technology. Stability over a long service life and the ability to scale production are central challenges. These requirements are especially important when comparing emerging materials with established module manufacturing processes.
Tandem photovoltaics: using more of the solar spectrum
A single-junction silicon cell has a practical efficiency ceiling because some incoming light is not absorbed, while energy from absorbed photons can be lost through thermalization. A tandem cell places two or more cells with different bandgaps together so they can use different portions of the solar spectrum more effectively.
Perovskites are of interest as potential high-bandgap top cells paired with silicon. Their tunable bandgap and limited absorption of below-bandgap light can suit this role. The objective is to raise conversion efficiency beyond what a single-junction silicon cell can achieve. In practice, the design must also address manufacturing, stability and the integration of the component cells.
What technology choices mean for PV projects
Technology development is not simply a race to the highest cell efficiency. For manufacturers and project decision-makers, relevant considerations include:
- Cost per unit of energy: manufacturing investment and maintenance should be assessed alongside lifetime energy output and any balancing or storage costs.
- Material efficiency: wafer thickness, silicon kerf losses, silver use and module materials can affect production costs.
- Energy yield: features such as bifacial cells, which can use light reflected from the rear, are among the approaches considered for increasing output.
- Scale and service life: a technology must move from laboratory performance to reliable large-area production and sustained operation.
Historical figures in the underlying technology overview illustrate the pace of deployment at that time: about 75 GW of PV modules were installed worldwide in 2016, and cumulative installations reached roughly 400 GW by the end of 2017. These figures provide historical context, not a measure of today’s market.
Conclusion
Crystalline silicon remains the foundation of PV manufacturing, with passivated contacts, back-contact designs and material savings offering paths for continued improvement. Thin-film technologies bring alternative absorber and production approaches, while perovskites are being explored for both standalone cells and silicon-based tandems. For industrial and project teams, the practical task is to evaluate efficiency together with cost, yield, lifetime and manufacturing readiness. That broader view is essential to determining which solar cell technologies can deliver lower-cost electricity in a specific application.