Access Official Technical PDF

Share Summary:LinkedInEmail

Solar energy systems convert radiation from the Sun into electricity or useful heat. For industrial facilities and automation projects, selecting an appropriate system begins with understanding the solar resource at the site, the form of energy required, and the costs associated with installation and operation. Photovoltaic (PV) panels and solar thermal collectors use sunlight in different ways, so their suitability depends on the application rather than on a single technology being universally preferable.

Solar energy systems start with the available resource

Solar radiation is the electromagnetic energy emitted by the Sun. The amount reaching a particular location varies with geographic position, time of day, season, local landscape, and weather. These factors affect how much energy a solar installation can receive and help determine whether a project is technically and economically viable.

Sunlight reaching the ground has direct and diffuse components. Direct radiation arrives from the direction of the Sun, while diffuse radiation has been scattered by the atmosphere. A surface may also receive sunlight reflected from the ground. Together, these contributions make up the total radiation received by a surface.

The distinction matters when considering system design. Concentrating collectors use mirrors or lenses to focus direct sunlight and can produce higher energy density, but they capture less of the diffuse component. Non-concentrating collectors can make use of diffuse sunlight as well. The balance between direct and diffuse radiation at a site therefore influences which collector approach is appropriate.

Solar resource data is commonly expressed as energy received per area, such as kilowatt-hours per square meter for PV systems, or as watts per square meter for radiation intensity. Measurements may refer to a horizontal surface or a surface that tracks the Sun. Comparing project estimates requires attention to the measurement basis and the conditions represented.

Photovoltaic panels and solar thermal collectors

Photovoltaic conversion

PV panels convert sunlight directly into electricity. In a silicon solar cell, light energy frees electrons, and the cell’s internal arrangement directs their movement to produce electric current. Individual cells are combined into panels, and the electrical output can serve connected equipment or a wider power system.

Panel technologies make different trade-offs. Monocrystalline and polycrystalline panels are silicon-based options, while thin-film panels use one or more layers of photovoltaic material on a substrate. The source material describes monocrystalline panels as offering higher efficiency and space use advantages at a higher price; polycrystalline panels as a lower-cost alternative; and thin-film panels as relatively inexpensive and flexible, but generally requiring more area. Actual selection should account for site conditions and the project’s available space and requirements.

Some PV installations use trackers to keep panels oriented toward the Sun. Tracking is optional for PV, and its role differs from concentrating solar thermal designs, where moving mirrors or lenses may be needed to maintain a focus on the receiver. Tracking adds system cost, so its use is a design consideration rather than an assumption.

Solar thermal applications

Solar thermal systems capture sunlight as heat. Low-temperature flat-plate collectors can heat water, including water for swimming pools or domestic and commercial use. Sunlight passes through a transparent cover and warms an absorber plate; heat is then transferred to liquid flowing through attached pipes. These systems may also support space heating where the application and site are suitable.

Higher-temperature systems may use evacuated tubes or concentrating collectors. Evacuated tubes reduce heat loss around the absorber. Concentrating systems use reflective or refractive components to direct sunlight onto a receiver. Parabolic troughs and parabolic dish systems are examples of reflective designs, while heliostat fields direct sunlight toward a shared absorber. Their designs, tracking needs, and costs differ from those of flat-plate collectors.

Thermal storage can shift when heat is used

Solar energy is not necessarily available at the time a facility needs heat. Thermal energy storage can help address this timing mismatch by retaining heat for later use. Sensible heat storage uses materials such as water, soil, sand, or gravel; water is commonly used because of its heat capacity, although the amount of energy that can be stored is a practical constraint.

Latent heat storage stores energy as a material changes phase. These materials are known as phase change materials. Chemical thermal storage instead uses a reversible chemical reaction to absorb and later release heat, but suitable reactions must meet practical requirements, including stability and reversibility. The source also describes solid-to-solid storage using plastic crystal material and solar ponds, which use a salt concentration gradient to collect and store heat.

These approaches are not interchangeable. The intended temperature range, storage duration, material behavior, and system design all matter. Storage can change when thermal output is available; it does not create additional solar energy.

Evaluate project economics beyond rated capacity

For a solar power plant, investment is a major part of total cost because the plant does not consume fuel. A useful comparison therefore considers expected energy production over time, as well as capital costs, operation and maintenance, financing, and plant lifetime. Levelized cost expresses costs across a system’s lifetime per unit of energy produced, but the result depends on assumptions such as interest rate, repayment method, and expected operating life.

Rated capacity alone is not enough to compare plants. The amount of electricity produced also depends on factors including location, shading, and whether the system tracks the Sun. Thermal storage can shift output to a later time, but does not by itself increase the plant’s total energy production. Project evaluations should distinguish between installed power, annual output, and the cost of producing energy.

Timing matters financially, too: investment may be committed before electricity production begins. The source notes that modular systems can begin producing as construction progresses, unlike projects that require completion before operation. Financing terms and construction schedules should therefore be considered alongside equipment costs.

Conclusion: Match the technology to the facility’s needs

For industrial decision-makers, solar project assessment is a practical exercise in matching resource, conversion technology, and energy demand. Establish how much direct and diffuse sunlight is available, decide whether the requirement is electricity or heat, and compare PV, thermal collection, tracking, and storage options accordingly. Then assess expected production and lifetime costs using clear assumptions. This approach provides a more meaningful basis for evaluating solar energy systems than panel type or rated capacity alone.

Access Official Technical PDF

About The Author