Solar panel temperature performance is an important consideration when estimating photovoltaic (PV) energy yield. Solar modules are commonly rated under Standard Test Conditions (STC), including a cell temperature of 25°C, but outdoor modules often operate at higher temperatures. Because heat can reduce output voltage and power, design decisions based on STC ratings alone may not reflect a system’s expected performance at a particular site.
A field comparison in Amman, Jordan, examined how cell temperature affected the energy yield of thin-film, mono-crystalline and poly-crystalline PV systems. Its results illustrate why module technology and local operating conditions should both be considered during preliminary system design.
Why temperature affects PV output
Solar cells convert sunlight into electricity through the photovoltaic effect. Their output depends on environmental conditions, particularly solar irradiance and cell temperature. When irradiance falls, a cell’s output current and voltage decrease. As temperature rises, current may increase slightly, but voltage decreases considerably. The combined effect can be a reduction in output power.
STC provides a consistent basis for comparing module ratings: 1,000 W/m² irradiance, a cell temperature of 25°C, no wind and an air-mass spectrum of 1.5. These are test conditions rather than a typical description of an operating PV array. In particular, cell temperature in the field can be substantially higher than 25°C, especially in hot conditions.
That difference matters when engineers estimate energy production. A module’s rated power is useful for comparing equipment, but it does not by itself capture how the module will perform across the temperatures and irradiance levels experienced at a real installation.
Comparing solar panel temperature performance in Amman
The study used monitoring and weather data from three south-facing PV systems at a test site in Amman. The systems used poly-crystalline, mono-crystalline and thin-film modules. They were selected for comparison because key design and operating factors were aligned: tilt and azimuth, mounting structure, inverter size, wiring characteristics, and cleaning method and schedule.
A nearby weather station, approximately 70 metres from the arrays, supplied measurements including ambient temperature and irradiance. The analysis compared actual energy yield recorded by the inverters with estimated yield calculated using measured irradiance and system specifications. The researchers used the difference to assess temperature-related deviations and calculate energy-yield temperature coefficients.
For the analysis, the modules were treated as ground-mounted, with cell temperature estimated as 20°C above ambient temperature. The calculated annual average cell-temperature increase above the STC reference was 12.53°C. The study attributed the observed yield deviations primarily to this temperature difference, while accounting for irradiance, array characteristics and module and inverter efficiency.
What the measured temperature coefficients show
The reported coefficients describe the change in energy yield for each 1°C increase in cell temperature above the STC reference. A more negative coefficient indicates a larger reduction in yield per degree under the study’s method.
- Thin-film: -0.0984% per °C
- Mono-crystalline: -0.109% per °C
- Poly-crystalline: -0.124% per °C
In this comparison, thin-film yield was less affected by temperature than the other two technologies, while poly-crystalline yield showed the largest temperature-related decrease. The study also reported annual deviations between actual and estimated yield of 15.4% for thin-film, 17.0% for mono-crystalline and 19.5% for poly-crystalline modules. These figures apply to the systems, location and analysis described; they should not be treated as universal values for every project or module.
Applying the findings to PV system design
For engineers and project decision-makers, the practical lesson is to evaluate module performance against the expected operating environment, rather than relying on STC ratings alone. Temperature response can influence predicted energy production, so it is relevant during technology selection and preliminary yield estimates.
Useful steps in a design review include:
- Consider local conditions. Assess expected irradiance and temperature, and recognize that operating cell temperature differs from the 25°C STC reference.
- Compare temperature coefficients. Review the relevant module data and use coefficients that correspond to the metric being estimated, such as power or energy yield.
- Keep system assumptions clear. Mounting configuration and other design factors affect the comparison. The study’s temperature estimate used a specific ground-mounted assumption, so its results should be applied with that context in mind.
- Separate site-specific evidence from general conclusions. The comparison supports a relative finding for the three systems studied in Amman, not a guarantee that the same ranking or coefficient will apply in every climate or installation.
Temperature coefficients can help translate site conditions into more realistic energy-yield expectations, but they are one part of a sound assessment. Consistent system design and transparent assumptions are also important when comparing technologies.
Conclusion
Cell temperature can reduce PV output, and the size of the effect varies by module technology. In the Amman field comparison, thin-film modules had the least negative energy-yield temperature coefficient, followed by mono-crystalline and then poly-crystalline modules. For PV designers and plant decision-makers, the results reinforce a practical principle: include temperature response and local operating conditions in technology selection and preliminary energy-yield calculations, while treating site-specific measurements as evidence for that context rather than a universal performance forecast.