Access Official Technical PDF

Share Summary:LinkedInEmail

SPRT calibration is central to realizing the International Temperature Scale of 1990 (ITS-90) across a broad temperature range. Standard platinum resistance thermometers (SPRTs) translate changes in platinum resistance into temperature values, using defined fixed points and mathematical interpolation. For laboratories and industrial measurement teams, the practical result depends not only on the calibration equations, but also on thermometer design, handling, thermal conditions and resistance measurement quality.

Understanding these elements helps engineers and technical decision-makers assess how temperature measurements are established, where uncertainty can enter, and why careful thermometer care matters.

How SPRT calibration realizes the ITS-90

The ITS-90 defines temperature sub-ranges using fixed points, such as the triple point of water and the freezing points of selected pure substances. Within a sub-range, an SPRT is calibrated at specified fixed points, and its resistance is measured at the temperatures of interest. The scale covers a wider range overall than any one thermometer design can practically serve; the guide’s focus is the range from the triple point of neon, 24.5561 K, to the freezing point of silver, 1234.93 K.

Rather than using absolute resistance values directly, the scale uses the resistance ratio W(T): the resistance at the temperature being measured divided by the thermometer’s resistance at the triple point of water. This normalization avoids a need for absolute resistance-standard traceability in SPRT calibration and can compensate for certain temperature-independent relative resistance changes. It does not, however, eliminate all sources of thermometer instability.

To determine temperature between fixed points, the ITS-90 uses reference functions and interpolation equations. Reference functions describe the behavior of selected high-quality platinum thermometers. Calibration measurements establish how an individual SPRT deviates from those functions. In practice, the calculation moves from measured resistance to a resistance ratio, applies the calibrated deviation, and then uses the reference function to obtain the ITS-90 temperature.

Why platinum thermometer design matters

Platinum is used because its resistance changes predictably with temperature over a wide range and it offers useful resistance to physical and chemical influences. SPRTs use high-purity platinum wire arranged to limit strain and supported so that mechanical changes do not distort its resistance-temperature behavior. Four-wire connections allow the instrument to carry current through two leads and measure voltage through two others, reducing the effect of lead resistance.

Three common designs serve different parts of the scale:

  • Capsule-type SPRTs are generally used at low temperatures and may also serve at selected higher fixed points. Their compact construction supports use in cryogenic systems, but they cannot be annealed in the same way as long-stem thermometers.
  • Long-stem SPRTs are used from cryogenic fixed points into the hundreds of degrees Celsius. Their longer silica sheaths and sensing elements are designed for immersion in fixed-point cells and furnaces.
  • High-temperature SPRTs extend use toward the silver point. They typically use a lower-resistance sensing element to limit errors associated with electrical leakage through insulation at high temperatures.

These designs involve different trade-offs in resistance, sensitivity, temperature capability and susceptibility to effects such as electrical leakage. Selecting the appropriate type is therefore part of establishing a reliable measurement process.

Protecting thermometer stability

Mechanical shock, vibration and strain can change an SPRT’s resistance. Shipping and routine handling should be managed to reduce these risks. For long-stem and high-temperature thermometers, annealing is used to reduce strain and other changes associated with use. Resistance checks at the triple point of water before and after treatment can help identify shifts. Capsule-type thermometers require particular attention because mechanical changes may cause persistent shifts.

High-temperature use adds further concerns. Contamination can affect platinum, while alkali compounds and other contaminants may promote devitrification of a fused-silica sheath. Careful cleaning before elevated-temperature use and protection from contamination help preserve the thermometer’s condition. Where a thermometer has been exposed to high temperatures, the measurement procedure should also account for the need to check its resistance and condition afterward.

Calibration quality also depends on using the thermometer in a reproducible state. For long-stem and high-temperature SPRTs, the target is a stable condition with appropriate annealing, controlled oxidation state and an equilibrium concentration of vacancies. A capsule-type SPRT may not be capable of reaching that same condition, making stability checks especially important.

Where measurement uncertainty enters

The calibration uncertainty of an SPRT is not determined by the interpolation equations alone. It includes uncertainty in resistance measurements at the fixed points and in resistance ratios, as well as the propagation of those uncertainties through the interpolation to the temperature being realized. The influence of each fixed point depends on the sub-range and the thermometer’s calibration data.

Additional effects arise during use. Heat conducted along the thermometer and its leads can disturb the local temperature, particularly when immersion is inadequate. Radiation can also affect the sensing element. Electrical measurement introduces considerations such as resistance-bridge performance, reference-resistor stability, self-heating from the measuring current, and connections or lead resistances.

The ITS-90 also has sub-range non-uniqueness: different prescribed sub-ranges can yield slightly different ITS-90 values for the same SPRT resistance. This reflects the scale’s interpolation structure and calibration consistency, rather than a different temperature measured by the thermometer. For high-accuracy work, the selected sub-range and its calibration points should be clearly understood when interpreting results.

Practical implications for measurement teams

For laboratories and organizations responsible for temperature measurement, SPRT calibration is best treated as a complete measurement system, not simply a certificate or a set of coefficients. The thermometer must be appropriate to the range, calibrated at the required fixed points, measured with suitable electrical methods, and used under conditions that limit heat flow, radiation and self-heating.

  • Choose a thermometer design suited to the operating temperature range.
  • Protect SPRTs from shock, vibration and avoidable contamination.
  • Monitor resistance at the triple point of water to identify changes in stability.
  • Account for immersion, thermal conduction, radiation and self-heating in the setup.
  • Use the correct ITS-90 sub-range and retain the associated calibration information.

In summary, the ITS-90 connects SPRT resistance measurements to temperature through fixed points, normalized resistance ratios and defined interpolation functions. Reliable realization depends on protecting the platinum sensing element, controlling measurement conditions and accounting for uncertainty throughout the calibration and use process. These practices help technical teams interpret SPRT measurements consistently and understand the limits of the temperature values they report.

Access Official Technical PDF

About The Author