The TC74VHC273 octal flip-flop provides eight clocked storage elements in one CMOS logic device. For control boards and digital interfaces, it can capture a group of input signals together and hold their states at the outputs until the next active clock edge. Its shared, active-low clear resets all eight outputs, while input protection supports selected mixed-voltage arrangements. Successful integration depends on understanding the clocking behavior, supply conditions and timing limits—not just the number of bits available.
How the TC74VHC273 octal flip-flop operates
Each of the device’s eight D-type flip-flops samples its D input on the positive-going edge of the common clock. The sampled logic state then appears at the corresponding Q output. Between clock edges, the outputs retain their previous states, even if the D inputs change.
This makes the part useful when several digital signals need to be registered at the same time. For example, a controller can present an eight-bit value at the D inputs and use one rising clock edge to capture that value. The device is not an octal latch: changing D while the clock is inactive does not, by itself, update Q.
The clear input, CLR, is active low. When CLR is held low, all Q outputs are forced to a low logic level regardless of the clock and D inputs. With CLR high, the flip-flops follow their normal clocked behavior. The clear is asynchronous in the functional sense: asserting it does not require a clock edge. Its timing requirements still need to be observed when it is released.
Voltage range and input protection
The specified operating supply range is 2.0 to 5.5 V, and the operating input-voltage range is 0 to 5.5 V. Toshiba also specifies input protection that allows input pins to receive 0 to 5.5 V regardless of the supply voltage. This can support interfacing between 5 V and 3 V systems, or arrangements involving separate supplies such as battery backup, while helping prevent damage from mismatched supply and input voltages.
That input protection should not be treated as permission to ignore system-level electrical limits. The output-voltage operating range is 0 to VCC, and input logic thresholds depend on the supply voltage. At VCC values from 3.0 to 5.5 V, the specified high-level input threshold is at least 0.7 × VCC and the low-level threshold is at most 0.3 × VCC. At VCC = 2.0 V, those limits are 1.50 V and 0.50 V, respectively. Check that the driving device’s output levels meet the TC74VHC273’s thresholds under the intended supply conditions.
The operating temperature range is −40 to 85°C. Unused inputs must be tied to VCC or ground rather than left floating. For reliable operation, keep supply, input and output conditions within their operating ranges; absolute maximum ratings are stress limits, not normal design targets.
Clock speed, propagation delay and timing
The datasheet gives a typical maximum clock frequency of 165 MHz at VCC = 5 V under its stated test conditions. The guaranteed maximum depends on supply voltage, output load and temperature. For example, at 5.0 ± 0.5 V and a 15 pF load, the listed maximum is 120 MHz at 25°C and 100 MHz across −40 to 85°C. With a 50 pF load, those limits are 80 MHz and 70 MHz. At 3.3 ± 0.3 V, the corresponding limits are lower.
These figures show why the headline frequency should not be used as a standalone design limit. Output loading affects both propagation delay and the maximum clock rate. The datasheet lists clock-to-output delay separately for 15 pF and 50 pF loads, with longer delays at the heavier load. Confirm that the timing budget accommodates the selected supply, load and operating-temperature range.
Other timing checks include:
- Clock pulse width: the clock must meet the specified minimum high- and low-level pulse widths.
- Setup and hold time: D must be stable for the required interval around the active clock edge.
- Clear pulse width and removal time: CLR must meet its minimum pulse-width requirement, and its release must be timed appropriately relative to clocking.
For example, at 5.0 ± 0.5 V, the minimum setup time is 4.5 ns and the minimum hold time is 1.0 ns under the listed conditions. The minimum clock pulse width is 5.0 ns for both high and low levels. Always refer to the datasheet limits for the actual supply, temperature and input conditions; typical values are not substitutes for guaranteed limits.
Power, noise and package considerations
The device is designed for low static power consumption: the specified quiescent supply current is 4 µA maximum at 25°C under the stated test condition, rising to a 40 µA maximum over the full temperature range. Dynamic consumption depends on switching activity and is described using the power-dissipation capacitance, CPD. The datasheet provides a calculation method for estimating operating current from CPD, supply voltage and input frequency, with an additional quiescent-current contribution per bit.
Noise immunity and output behavior also matter in digital systems. The datasheet specifies minimum static noise-immunity values of 28% of VCC and provides dynamic noise-characteristic limits under defined test conditions. These parameters should be reviewed alongside signal integrity, load and board-level design requirements.
The TC74VHC273 is pin- and function-compatible with the 74ALS273, which can help when evaluating a logic-family alternative. Confirm electrical characteristics and timing against the requirements of the existing circuit rather than assuming that compatibility means identical behavior in every condition. The device is available in SOP20 and VSSOP20 packages; select the package that fits the board design and assembly requirements.
Design implications
The TC74VHC273 combines eight rising-edge-triggered storage channels, a common active-low clear and CMOS operation across a 2.0 to 5.5 V supply range. Its input protection can be useful in mixed-voltage designs, but designers still need to verify logic thresholds, output loading, clock frequency and reset timing. Tie unused inputs to a defined logic level, maintain the specified operating conditions, and treat absolute maximum ratings as limits to avoid—not targets for routine operation. These checks help determine whether the device is an appropriate fit for a control, interface or signal-registration stage.