Access Official Technical PDF

Share Summary:LinkedInEmail

Thermal interface materials are used in electronic assemblies to improve heat transfer between a heat-generating component and a heat sink, chassis or other heat spreader. For automation equipment and other electronics, the challenge is not simply choosing a material with a high thermal conductivity. Surface texture, assembly pressure, interface thickness and electrical isolation all affect how the material performs in the completed assembly.

Thermally conductive gap pads are one option when uneven surfaces, air gaps or stack-up variations make direct contact difficult. Understanding the distinction between material properties and assembly-level thermal behavior helps engineers and integrators make a more suitable selection.

Thermal interface materials and the air-gap problem

Air trapped between a component and a heat sink can impede heat transfer. A gap-filling material replaces some of that air and conforms to surface irregularities, helping create more consistent contact across the interface. This is particularly relevant where components or mounting surfaces are stepped, rough, or separated by varying distances.

Gap pads are designed for this type of interface. They are available in different thicknesses, degrees of softness, reinforcement constructions and thermal conductivity levels. Depending on the material, a pad may also provide electrical isolation, temporary tack to hold it in place during assembly, or resistance to puncture, shear and tearing.

Conductivity is not the same as thermal impedance

Thermal conductivity describes an inherent material property: how readily heat flows through a material for a given area, temperature difference and thickness. It is useful when comparing materials, but it does not alone determine the heat-transfer performance of an installed interface.

Thermal impedance describes a particular assembly. It relates the temperature difference between two surfaces to the steady-state heat flow through them. As a result, it reflects not only the material but also how the material is installed and measured. Increasing contact area can reduce impedance, while increasing interface thickness can increase it. Under ideal conditions, greater mounting pressure can also reduce impedance by improving contact. Measurement method and elapsed time can affect the reported result.

Thermal resistance is another related term, describing opposition to heat flow through a unit area of material across a specified thickness. Unlike conductivity, resistance varies with thickness. These distinctions matter when interpreting product data: a conductivity value is not a complete prediction of performance in a specific assembly.

How to select a thermal gap pad

Start with the physical and electrical requirements of the interface, then evaluate thermal properties in that context. Key questions include:

  • What gap must be filled? Identify the final space between the mating surfaces, including stack-up tolerances and height variation. The relevant pad thickness is the installed, or resultant, thickness.
  • How much assembly pressure is available? A stiff material may not conform well when mounting force is limited. A softer, lower-modulus option may be more appropriate where component stress must be minimized.
  • Are the surfaces rough or stepped? Conformability helps the material contact uneven topography and reduce air voids at the interfaces.
  • Is electrical isolation required? Gap Pad materials are electrically isolating, but the source cautions that they are intended to fill gaps, not to guarantee isolation in high-stress applications. The design must account for the actual electrical and mechanical conditions.
  • What handling demands apply? Reinforcement can improve ease of handling and resistance to puncture, shear and tearing. Unreinforced constructions may offer additional compliance.
  • How will the part be positioned? Natural tack or an adhesive option may help hold a pad during assembly. Tack varies by product; adhesive-backed versions also have shelf-life considerations.

Matching material characteristics to the application

Product examples show how these properties involve trade-offs. Gap Pad VO has a stated thermal conductivity of 0.8 W/m·K and uses a rubber-coated fiberglass carrier for handling. Gap Pad VO Soft also has a conductivity of 0.8 W/m·K, with lower hardness for applications requiring less stress on components. Gap Pad VO Ultra Soft has a gel-like modulus, is intended for low-stress applications, and has a stated conductivity of 1.0 W/m·K.

For applications where silicone sensitivity is a concern, Gap Pad 1000SF is described as a silicone-free, electrically insulating material. Its stated conductivity is 0.9 W/m·K, and it uses fiberglass reinforcement. For a higher conductivity example, Gap Pad 2500 is an unreinforced material rated at 2.7 W/m·K, with a soft but elastic construction intended for mid-pressure applications. These examples illustrate why conductivity should be considered alongside compliance, reinforcement, pressure and application needs—not used as the sole selection criterion.

Gap pads can be supplied as sheets or die-cut parts, and some are also available in roll form. Choosing a form that suits the assembly process can simplify placement and handling. Confirm the required thickness, configuration and surface tack with the material specifications for the specific product under consideration.

Test data and validation

Thermal data depends on the method used to measure it. The selection guide describes thermal impedance testing using an ASTM D5470-based method and notes that its testing conditions, including pressure, area and time, affect interpretation. It also identifies a modified method for testing Gap Pad materials at low pressure. Engineers should therefore compare data obtained under relevant, understood conditions and validate the interface in the intended assembly.

Other design checks may include temperature range, dielectric breakdown, volume resistivity, flammability, outgassing or silicone extraction, depending on the application. These properties differ among materials and should be checked against the specific product data rather than assumed from the general category.

Practical implications for thermal design

Effective thermal interface selection begins with the assembly: the gap, surface topography, available mounting pressure, component sensitivity and electrical requirements. Conductivity helps narrow options, while thermal impedance and interface resistance depend on the installed construction and contact conditions. A compliant material can help fill irregular gaps; reinforcement can aid handling; and tack can support placement, but each characteristic should match the design priorities.

For industrial automation engineers and technical decision-makers, the practical approach is to define the mechanical and electrical constraints first, review material data with its test conditions in mind, and evaluate the chosen interface in the actual assembly. This keeps thermal management decisions grounded in both material properties and the realities of installation.

Access Official Technical PDF

About The Author