Access Official Technical PDF

Share Summary:LinkedInEmail

Three-terminal solar cells offer a way to combine the spectrum-harvesting approach of multijunction photovoltaics with independent electrical access to each subcell. The heterojunction bipolar transistor solar cell (3T-HBTSC) uses a compact n-p-n or p-n-p semiconductor structure, but is designed to operate as a photovoltaic device rather than as a conventional bipolar transistor. Its proposed value lies in pairing tandem-style light absorption with reduced sensitivity to spectral changes and a layer architecture that does not require a tunnel junction.

How a three-terminal solar cell works

The basic 3T-HBTSC has three semiconductor layers: a high-bandgap emitter, a high-bandgap base and a lower-bandgap collector. Together, the emitter and base form the top subcell, which absorbs higher-energy photons. Light that passes through reaches the base-collector junction, where the lower-bandgap collector can absorb lower-energy photons.

The base is shared by both subcells and serves as a common electrical contact. Separate external circuits connect the base to the emitter and collector, allowing the two subcell currents to be extracted independently. This is a key distinction from a conventional two-terminal tandem, where the subcells are series-connected and their currents must be matched.

Although the layer sequence resembles a bipolar junction transistor, the intended operation is different. The structure must prevent transistor action from coupling the subcells’ electrical behavior. The paper identifies a higher doping level in the middle layer than in the top layer, a larger middle-layer bandgap, or both, as ways to suppress transistor gain and help maintain independent quasi-Fermi-level separation in each subcell.

Why independent current extraction matters

In a series-connected multijunction cell, a subcell producing more current than another cannot deliver all of its excess photocurrent through the series circuit. Changes in sunlight spectrum can therefore move the device away from its current-matched operating condition. Atmospheric filtering and the Sun’s changing position alter spectral conditions over time; degradation that affects one junction can also constrain the output of the complete tandem.

A 3T-HBTSC provides a separate current path for each subcell. This reduces the direct dependence of overall current extraction on current matching, potentially helping the device make better use of changing illumination conditions. The architecture also avoids the tunnel junction used to connect subcells in a conventional monolithic two-terminal tandem. In the proposed dual-junction structure, three semiconductor layers replace the more complex arrangement of two p-n junctions and a tunnel-junction layer.

Four-terminal tandems also extract subcell currents independently and do not require a tunnel junction. However, the compared architecture requires at least four semiconductor layers and an additional front contact grid. Both three- and four-terminal designs still face a practical challenge: current in the shared middle layer must be collected laterally, so contact layout and resistance remain important design considerations.

Three-terminal solar cells across material platforms

Crystalline silicon with a low-bandgap rear junction

One proposed silicon architecture adds an In(Ga)As nanowire junction to the rear of a crystalline-silicon cell. Silicon absorbs much of the higher-energy light, while the lower-bandgap III-V nanowires are intended to capture infrared photons that the silicon junction does not absorb. Because the nanowires are added as a separate collector junction, the concept aims to extend spectral absorption without replacing the silicon cell’s central role.

Manufacturing would involve forming the silicon junction, preparing openings in a thin silicon oxide layer, growing In(Ga)As nanowires in those openings and forming contacts to the silicon base and nanowire collector. The additional material and contact processing increase fabrication complexity and cost. The paper’s analysis therefore emphasizes that the efficiency gain would need to justify those added costs; the proposed design is an architecture for investigation, not a demonstrated commercial upgrade.

Adding an amorphous-silicon top subcell

A second option builds on silicon heterojunction (HIT) technology by adding an amorphous-silicon top subcell. The higher-bandgap a-Si:H layer absorbs part of the high-energy sunlight, while the crystalline-silicon wafer remains the main absorber for lower-energy photons. Separate front contacts serve the top and middle layers, with a rear contact to the silicon collector.

This approach draws on existing a-Si:H and silicon heterojunction processing knowledge. The trade-off is that photons absorbed in the top cell are no longer available to the silicon subcell, whose contribution is consequently reduced. The intended benefit is the additional voltage from the higher-bandgap subcell, with the three-terminal connection allowing its output to be collected separately.

III-V designs for concentration and space

III-V semiconductors are proposed for high-efficiency applications including concentrator photovoltaics and space power systems. Candidate material combinations include AlGaAs/GaAs and GaInP/(In)GaAs. Independent extraction may be useful where illumination spectra vary or where radiation affects one junction more than another, since the output of a separate subcell need not be constrained in the same way as a series-connected tandem.

Implementation still requires careful engineering. Front-side emitter and base contacts need to limit lateral resistance while minimizing shading of incoming light. Etching, contact formation and the required safety margins also affect processing and optical design. These constraints matter especially in concentrated-light cells, where grid geometry is an important part of the device design.

Perovskite and silicon combinations

A perovskite-silicon 3T-HBTSC pairs a tunable-bandgap perovskite top subcell with a crystalline-silicon bottom subcell. The proposed arrangement uses separate contacts for the perovskite-related layers and silicon, while avoiding the need to form a silicon p-n junction in the described implementation. Its appeal is the combination of perovskite material flexibility with established silicon technology.

Perovskite devices nevertheless face challenges, including material stability and concerns related to lead. A three-terminal configuration does not remove those issues; rather, it offers an alternative way to electrically integrate the two absorbers and to accommodate differences in their photocurrents.

Practical considerations for system design

Independent subcell outputs introduce a system-level task: connecting three-terminal cells into useful modules. Module interconnection is not automatically straightforward for every voltage relationship between the top and bottom subcells. Voltage-conversion electronics may be needed, and the integration of additional junctions into higher-order structures remains an area for further development.

For engineers and technical decision-makers assessing the concept, the main considerations are:

  • Contact and resistance design: the shared middle layer needs an effective lateral current path.
  • Optical losses: front grids and contact layouts must collect current without unnecessarily shading active material.
  • Process compatibility: each material pairing brings its own deposition, etching and contact requirements.
  • Module integration: cell-level current independence must be matched with a practical approach to voltage conversion and wiring.

Conclusion

Three-terminal solar cells provide a distinct route to tandem photovoltaic operation: sequential light absorption, separate subcell current extraction and no tunnel junction in the proposed basic structure. Silicon, III-V and perovskite-based designs illustrate how the concept could be adapted to different applications and manufacturing approaches. Their practical potential depends not only on the absorber materials, but also on lateral contact design, fabrication cost and module interconnection. These are essential considerations when evaluating whether a three-terminal architecture can translate its device-level advantages into useful system performance.

Access Official Technical PDF

About The Author