Designing a host port that carries both high-speed USB and DisplayPort over USB Type-C involves more than selecting a connector. The system must route signals according to the negotiated Alt Mode configuration and account for loss in board traces and cables. The TUSB1146 USB Type-C redriver addresses these needs by combining a crosspoint switch with linear redriving for USB data rates up to 10 Gbps and DisplayPort rates up to 10 Gbps (UHBR10).
For engineers and system integrators, the device’s practical value lies in its configurable lane routing, receiver equalization, and support for both GPIO and I2C control. Understanding how those functions fit into the host design helps guide component configuration and signal-integrity decisions.
USB Type-C redriver for multiple Alt Mode configurations
The TUSB1146 is intended for downstream-facing host ports, including notebooks, desktops, tablets, and docking stations. It supports the VESA DisplayPort Alt Mode pin assignments C, D, and E, corresponding to two principal high-speed configurations: four DisplayPort lanes, or two DisplayPort lanes alongside USB SuperSpeed.
- USB-only: Routes the high-speed USB path through the switch.
- USB plus DisplayPort: Allocates two lanes to DisplayPort while retaining USB SuperSpeed.
- DisplayPort-only: Uses four lanes for DisplayPort.
Because a USB Type-C plug can be inserted in either orientation, the system also needs to account for lane flipping. The TUSB1146 uses a flip-control input in GPIO mode or a corresponding I2C setting to select the appropriate routing. The USB Power Delivery controller can coordinate this state with the port’s mode and orientation.
The device is described as protocol-agnostic and can also support other USB Type-C Alt Mode interfaces, such as HDMI Alt Mode. This capability does not change the need for the system designer to configure routing and signal conditioning appropriately for the selected interface.
How redriving addresses channel loss
High-speed signals can lose energy as they travel through PCB traces and cables. Channel loss can contribute to inter-symbol interference (ISI), in which signal energy from one bit affects the interpretation of later bits. A linear redriver compensates for this loss by applying receiver equalization and driving the signal onward. It does not decode the USB physical-layer traffic.
The TUSB1146 provides selectable equalization for USB and DisplayPort receiver paths. The appropriate setting depends on insertion loss before the device’s receiver. Designers can set equalization using four-level configuration pins or, in I2C mode, registers. USB upstream, USB downstream, and DisplayPort have separate equalization controls, allowing the settings to be matched to the relevant channel paths. The device specifies up to 12 dB of equalization at 5 GHz.
Fixed and adaptive USB receiver equalization
For the downstream-facing USB receivers, the device offers fixed equalization, Fast Adaptive EQ, and Full Adaptive EQ. Fixed EQ applies one selected setting across connected-device scenarios. Fast Adaptive EQ distinguishes between a short, lower-loss connection and a longer, higher-loss connection, then selects between two predetermined settings. Full Adaptive EQ determines an appropriate setting when a USB device is inserted, including for channels that fall between those two cases. Full AEQ is disabled by default and can be enabled through a register.
Adaptive equalization can be useful when the channel varies between use cases. The data sheet gives maximum determination times of 60 microseconds for Fast AEQ and 300 microseconds for Full AEQ. These timing figures describe the device’s equalization process; they do not replace system-level validation of the complete signal path.
Managing USB and DisplayPort behavior
USB and DisplayPort differ in how their links operate, so the redriver monitors relevant physical-layer conditions rather than interpreting USB protocol packets. For USB, it supports the defined U0, U1, U2, and U3 power states and monitors conditions such as receiver termination, electrical idle, and low-frequency periodic signaling (LFPS). Its LFPS detector disables receiver equalization while LFPS is detected and enables equalization for other signaling according to the selected settings.
In DisplayPort mode, the TUSB1146 can snoop native AUX transactions. It monitors writes to the DisplayPort configuration registers for lane count and power state, then enables or disables lanes accordingly. This lane management is intended to reduce power when fewer lanes are active or the sink is in the specified low-power state. AUX snooping is enabled by default; it can be disabled through a register, or through the CAD_SNK pin in GPIO mode. When snooping is disabled using CAD_SNK, all four DisplayPort lanes are active.
The device also routes the DisplayPort AUX signals to the USB Type-C SBU pins according to connector orientation. Hot-Plug Detect provides another control input: when HPDIN remains low for more than 2 ms, DisplayPort lanes are disabled while the AUX-to-SBU switch remains closed.
Choosing GPIO or I2C configuration
GPIO mode provides pin-based selection for USB-only, two-lane DisplayPort plus USB, four-lane DisplayPort, and power-down states. It offers a straightforward approach when the system’s configuration can be controlled through fixed logic signals. In I2C mode, the same operating configurations can be selected through registers, alongside additional programmable controls.
The TUSB1146 operates from a 3.3 V supply, with a recommended supply range of 3.0 V to 3.6 V. It is available in commercial and industrial temperature versions: the TUSB1146 is rated for 0 °C to 70 °C, while the TUSB1146I is rated for −40 °C to 85 °C. Both use a 40-pin WQFN package with a nominal 4 mm × 6 mm body.
In either control mode, configuration timing and routing need to be considered during startup and mode transitions. GPIO control pins have specified setup and hold requirements, and GPIO transitions between USB and four-lane DisplayPort require a minimum overlap. The device also requires external components and connections specified for particular paths, including AC-coupling capacitors on relevant high-speed and AUX interfaces. Designers should use the device documentation to confirm pin assignments, termination, coupling, and layout details for their implementation.
Practical implications for system design
The TUSB1146 brings lane switching and signal conditioning together for USB Type-C host designs that need to support USB SuperSpeed and DisplayPort Alt Mode. Its fixed or adaptive equalization options provide ways to address different channel-loss conditions, while GPIO and I2C control allow the configuration approach to match the broader system architecture.
Successful integration still depends on defining the intended Alt Mode configurations, coordinating orientation and mode control, selecting equalization for the actual channel, and following the device’s power, coupling, and layout requirements. For teams designing notebooks, docks, or other host platforms, those decisions are central to building a USB Type-C port that routes the required interfaces and maintains signal integrity across the designed channel.