Access Official Technical PDF

Share Summary:LinkedInEmail

Vertical GaN power devices are being developed to address the need for efficient power conversion as energy conservation and electrification become increasingly important. A key challenge is reducing device resistance without sacrificing the ability to withstand voltage. Toyoda Gosei’s vertical GaN-MOSFET development illustrates one approach: adding a current distribution layer (CDL) to spread electron flow through the drift region. The resulting device demonstrated 100-A current operation on a single chip.

Why develop a vertical GaN power device?

Gallium nitride has material properties that make it attractive for power semiconductor development. Much of the progress in GaN power transistors has involved lateral AlGaN/GaN field-effect transistors, which use a high-mobility two-dimensional electron gas to achieve low on-resistance. Silicon substrates can also support low-cost fabrication and large substrate diameters.

A limitation of the lateral structure is that maintaining high voltage withstand capability requires substantial spacing between the gate and drain. That spacing can increase chip size and make it harder to reduce dimensions or increase integration.

In a vertical FET, the drift layer’s thickness supports the voltage withstand function. This structure can therefore make smaller device layouts and higher integration more practical. Toyoda Gosei’s development focused on a vertical GaN-MOSFET using a GaN substrate, with honeycomb cell design and wiring intended to support parallel operation. The broader goal was to combine low resistance with high withstand voltage.

How a current distribution layer reduces resistance

In a FET, electrons travel from the source toward the drain through the channel and drift layer. As they move from the channel into the drift layer, their path spreads. Close to the channel, however, the current is concentrated in a relatively narrow part of the drift region. This limited pathway contributes to higher resistance.

The CDL is inserted between semiconductor layers to help the electron pathways spread laterally, or in the plane of the device. By widening the region carrying current, the layer can reduce the resistance associated with the concentrated flow near the channel. In practical terms, it is intended to make more of the drift region available for conduction rather than leaving current confined to a narrow path.

Positioning the layer to balance resistance and voltage

Where the CDL is placed matters. Moving it closer to the channel can encourage current to spread earlier in the drift layer, which is desirable for lowering resistance. But the region near a p-n junction can contain a depletion layer with relatively few majority carriers. Forming the CDL in that area may require a higher impurity concentration.

That higher concentration can increase the electric-field strength at the p-n junction under off-state conditions. The result may be reduced voltage withstand capability—the opposite of the desired balance between low resistance and robust voltage handling.

Toyoda Gosei used simulations to examine CDL positioning. The objective was to identify a location that provides a useful current-distribution effect while reducing the layer’s susceptibility to depletion-layer effects. The simulations identified a position where the design could maintain high withstand voltage while benefiting from improved current spreading.

Device tests and 100-A operation

To evaluate the approach, small-element vertical GaN-MOSFETs were fabricated both with and without a CDL. In a comparison conducted at a drain voltage of 0.5 V and a gate voltage of threshold voltage (Vth) plus 20 V, the device with the CDL produced 1.17 times the drain current of the device without it. The reported withstand voltages were the same for both structures.

The development then moved beyond small-element comparison. A chip incorporating the CDL was fabricated and tested for large-current operation. The demonstrated result was 100 A on a single chip, showing the potential of the structure for high-current vertical GaN power devices.

For engineers assessing the result, the distinction between the two demonstrations is important: the 1.17-times drain-current comparison was made on small-element devices under specified test conditions, while the 100-A figure describes large-current operation demonstrated on a CDL-equipped chip. These results support the value of current spreading, but do not by themselves establish performance under every application’s operating conditions.

Implications for power semiconductor development

The CDL addresses a design trade-off that is central to power device engineering. A vertical structure offers a way to support voltage through the drift layer, while the added layer helps reduce resistance by spreading current. Its placement must be selected with both on-state conduction and off-state electric-field distribution in mind.

For system integrators and technical decision-makers, the work highlights why device architecture, semiconductor-layer design, and simulation need to be considered together. A feature that improves current flow can also affect electric-field behavior, so optimization cannot focus on resistance alone.

Conclusion

A current distribution layer provides a structural method for widening electron pathways in a vertical GaN-MOSFET. In the reported tests, it increased drain current by a factor of 1.17 under the stated comparison conditions without changing the measured withstand voltage, and a CDL-equipped chip demonstrated 100-A operation. Further reliability improvements were identified as part of the work needed to advance high-performance GaN power semiconductors toward practical use.

Access Official Technical PDF

About The Author