Wafer-level EDMR (electrically detected magnetic resonance) offers a way to investigate electrically active defects in semiconductor devices without first removing individual devices from a wafer. By combining magnetic resonance measurements with a conventional wafer-probing station, the technique connects defect analysis more directly with device electrical characterization. A 2019 demonstration applied the approach to processed 4H-SiC MOSFETs, using a non-resonant microwave probe and frequency-swept measurements.
The central idea is to detect resonance through a change in device current rather than through microwave power reflected by a conventional electron paramagnetic resonance (EPR) resonator. This makes EDMR sensitive to defects that influence device operation, while the wafer-probing setup provides access to electrical contacts and device biasing.
Why integrate EDMR with wafer probing?
Traditional EDMR arrangements often adapt an EPR spectrometer for electrical measurements. Preparing a device for a resonator can require dicing the wafer, mounting the sample, and creating electrical connections suited to the instrument. Those steps differ from common wafer-level characterization workflows, where probes are used to measure electrical behavior across devices on a wafer.
In the demonstrated wafer-level arrangement, the device remains in its processed wafer. A permanent magnet supplies the static magnetic field, while a small, non-resonant coaxial probe applies the microwave magnetic field near the device. Separate electrical probes provide bias and measure current. This removes the need for a microwave cavity or resonator and allows the microwave probe and electrical contacts to be positioned independently.
The approach was demonstrated on n-channel 4H-SiC MOSFETs. Silicon carbide is a wide-bandgap semiconductor used in high-power and high-temperature device applications. The measurements focused on a silicon-vacancy defect associated with the SiC/SiO2 system and examined its contribution to several spin-dependent current mechanisms.
How wafer-level EDMR detects defects
In EDMR, a magnetic field and microwave excitation drive a spin system into resonance. At resonance, changes to the spin state can affect a spin-dependent electrical process, such as recombination. The resulting change in device current is the measured signal. This provides information about paramagnetic defects that participate in current-limiting or recombination behavior.
The apparatus uses a fixed magnetic field, B0, and sweeps microwave frequency to find the resonance condition. A non-resonant probe supplies the microwave magnetic field, B1, near the device. Because the probe is broadband, it can operate across the frequency range used for the measurements without the frequency-selective behavior of a resonant cavity. The system supports both slower, modulated frequency sweeps and rapid frequency scans.
Frequency-swept measurements offer an alternative to changing the magnetic field while holding the microwave frequency fixed. The resonance relationship between frequency, magnetic field, and the spin’s g-value allows the resulting spectra to be compared. In the reported work, the same silicon-vacancy response was observed using the wafer-level setup and a conventional resonator-based EDMR measurement.
Multiple biasing methods reveal different defect activity
Changing the device biasing scheme changes which current processes contribute to the EDMR signal. That flexibility is important because defects may affect different parts of a MOSFET or participate in different operating mechanisms.
- Spin-dependent recombination (SDR): Forward biasing the source-to-body junction produces recombination current in the junction depletion region. The reported measurements detected the silicon-vacancy response through this current.
- Bipolar amplification effect (BAE): Biasing the transistor in a subthreshold regime makes source-to-drain transport sensitive to recombination near the channel interface. The study used this method to examine the defect’s contribution to the measured current.
- Spin-dependent charge pumping (SDCP): A waveform applied to the gate cycles the MOSFET through accumulation and inversion, alternately filling and emptying interface states. The resulting recombination current can reveal defects associated with the interface.
These modes provide complementary views of defect behavior. Rather than treating a MOSFET as a single electrical structure, engineers can adjust the biasing conditions to emphasize junction, channel, or interface-related processes. The measurements in the study used the different modes to observe the same defect system in distinct current pathways.
Rapid scans and spatially resolved measurements
Rapid frequency-scan EDMR is another capability enabled by the broadband, non-resonant measurement arrangement. The reported system used a voltage-controlled oscillator and attenuator to sweep frequency, alongside current-measurement electronics and a high-speed oscilloscope. The current amplifier’s bandwidth limited the achievable scan rate, illustrating an important system-level consideration: faster microwave sweeps require electrical detection electronics capable of following the resulting signal.
The study also demonstrated a basic form of spatially resolved EDMR by moving the microwave probe laterally across a MOSFET. The measured response varied with probe position and was stronger when the probe was located over the gate region under the relevant bias conditions than when it was positioned over the drain. This offers a way to explore where a response originates within a device, although the authors characterized the demonstrated spatial profiling as crude. Probe size, positioning control, and the excited region’s extent affect the resolution.
Practical implications for reliability and characterization
For semiconductor reliability and process-development teams, the main significance is the combination of defect-sensitive measurement with wafer-level electrical access. The method can examine devices in their processed state and switch among biasing schemes without the sample preparation associated with conventional resonator measurements. It may therefore support investigations that connect electrically active defects with device behavior more directly.
The technique does not eliminate experimental constraints. Accurate measurements depend on positioning the device in a sufficiently uniform magnetic-field region, maintaining reliable probe contact, and selecting suitable current-amplifier bandwidth for the scan method. Spatial profiling also depends on the microwave probe geometry and placement. These factors should be considered when assessing whether the method fits a particular device or laboratory workflow.
Conclusion
Wafer-level EDMR brings electrically detected magnetic resonance into a semiconductor wafer-probing station, using a non-resonant microwave probe and device-current detection to study defects in processed MOSFETs. Demonstrations on 4H-SiC devices show that the setup can support junction and interface-sensitive measurements, slow and rapid frequency scans, and exploratory spatial profiling. For engineers and technical decision-makers, its practical value lies in adding defect-sensitive analysis alongside wafer-level electrical characterization, while keeping measurement limits and probe configuration in view.