Semiconductor reliability teams need to understand not only how a device performs, but also which defects influence its behavior. Conventional electrical measurements at a wafer probing station can identify performance changes, yet they do not by themselves reveal the atomic-scale nature of the defects involved. Wafer-level EDMR (electrically detected magnetic resonance) brings a defect-sensitive measurement technique into a conventional probing environment, allowing researchers to investigate electrically active defects in individual, fully processed devices.
The approach is relevant to engineers and technical decision-makers evaluating reliability characterization methods for increasingly complex semiconductor devices. By combining magnetic resonance with electrical measurement at the wafer level, it offers a way to connect device behavior with information about the defects that may affect it.
What electrically detected magnetic resonance measures
Electron paramagnetic resonance (EPR) identifies paramagnetic defects by applying a magnetic field and microwave energy. When defect spins reach resonance, they absorb energy. In conventional EPR, the measurement detects a change in microwave power reflected by a resonant cavity.
EDMR detects resonance through a different signal: a spin-dependent change in a device’s current or voltage. In certain device processes, the behavior of defect spins affects electrical activity such as recombination. When the magnetic resonance condition changes the spins’ state, the device current can change as well. Measuring that electrical response makes it possible to study defects that participate in the device’s operation.
This electrical detection is particularly valuable for small or technologically relevant structures, where conventional EPR may not provide sufficient sensitivity. The reported work describes EDMR as at least ten million times more sensitive than conventional EPR, helping address the measurement needs of advanced device structures.
How wafer-level EDMR fits a probing station
Traditional EDMR arrangements can require specialized equipment and sample preparation. The wafer-level method instead modifies a commercially available semiconductor probing station. It retains electrical probes for biasing the device and measuring its current, while adding the components needed to establish magnetic resonance conditions.
A permanent magnet supplies the static magnetic field. A small, non-resonant near-field microwave probe provides the oscillating magnetic field required for resonance. This probe replaces the conventional microwave cavity or resonator, simplifying the detection arrangement and allowing measurements to be made on a device directly on the wafer.
Because the device remains in the probing station, the method can avoid dicing the wafer, mounting a sample, and wire-bonding device contacts for the measurement. Electrical bias conditions can be applied through the station’s probes, and the resulting spin-dependent current can be monitored as the magnetic resonance conditions are varied.
Wafer-level EDMR and semiconductor defect analysis
The demonstration used planar 4H-SiC n-channel MOSFETs and identified silicon-vacancy defects associated with the device response. Silicon carbide is a relevant example because defects at the semiconductor–insulator interface and within the device can influence electrical behavior. The results show how wafer-level EDMR can provide defect information while working with fully processed transistor structures.
The setup supported several EDMR measurement schemes, each providing a different view of electrically active defects:
- Spin-dependent recombination (SDR): Measures changes in recombination current, including activity in a transistor’s source-body junction. The observed response can help identify defects participating in recombination.
- Bipolar amplification effect (BAE): Uses a gate bias in the sub-threshold regime so that recombination events across the channel influence source-drain current. This approach can provide information about interface traps affecting device current.
- Spin-dependent charge pumping (SDCP): Applies a changing gate waveform to cycle the device between accumulation and inversion. Alternately filling interface states with holes and electrons allows investigation of defects across much of the semiconductor bandgap.
These methods illustrate why measurement biasing matters. A standard electrical test and an EDMR measurement do not necessarily emphasize the same device processes. Selecting an appropriate bias scheme helps direct the measurement toward a region or defect-related mechanism of interest.
Implications for reliability characterization
For semiconductor reliability laboratories, the practical value of wafer-level EDMR is the ability to pair electrical behavior with defect-sensitive analysis on an unaltered wafer. This can make it easier to examine individual devices in a probing station without the sample-preparation steps associated with conventional EDMR measurements. The reported work demonstrated multiple biasing approaches on SiC MOSFETs and found signal-to-noise performance at least comparable to, and likely somewhat better than, a conventional EDMR spectrometer.
The technique does not replace routine electrical characterization. Instead, it adds a method for probing the physical and chemical characteristics of defects that ordinary current or voltage measurements may not identify. For teams investigating reliability-limiting imperfections, that distinction can help connect an observed electrical response to the underlying defect population.
Although the demonstration focused on SiC devices, the authors indicate that the approach may also apply to other MOSFETs, bipolar junction transistors, and memory devices. Its broader relevance will depend on the device and measurement question, but the probing-station format provides a platform for exploring EDMR across different structures.
Conclusion
Wafer-level EDMR integrates electrically detected magnetic resonance with conventional semiconductor probing, bringing atomic-scale defect analysis closer to routine device characterization. Its non-resonant microwave probe avoids the need for a standard resonance cavity, while electrical biasing enables measurements of spin-dependent processes in fully processed devices. For reliability engineers and semiconductor characterization teams, the method offers a complementary way to investigate defects behind device behavior, with demonstrated applications in SiC MOSFETs and potential use across other device types.