Access Official Technical PDF

Share Summary:LinkedInEmail

Wide bandgap power electronics based on silicon carbide (SiC) and gallium nitride (GaN) offer engineers alternatives to conventional silicon devices when power-conversion systems must handle demanding operating conditions. Their potential advantages include higher operating temperatures, faster switching and lower losses in appropriate applications. For industrial automation and other power-intensive sectors, however, technical promise alone is not enough: cost, reliability, packaging and supply-chain maturity all affect whether these devices make sense at system level.

A PowerAmerica technology roadmap framed these opportunities and barriers as priorities for the SiC and GaN ecosystem. Its central message remains useful for technical decision-makers: adoption requires coordinated progress in devices, manufacturing, system design and workforce capability.

Why wide bandgap power electronics matter

Power electronics convert electrical power and control characteristics such as voltage, current and frequency. They are essential across systems ranging from electronic equipment to electric vehicles and renewable-energy installations. The semiconductor material used in a power device influences how it performs under electrical and thermal stress.

SiC and GaN have wider bandgaps than silicon, a material property associated with their ability to operate under conditions that challenge conventional silicon devices. The roadmap describes SiC and GaN as the most mature wide bandgap options for power-electronics applications, while also noting research into materials such as gallium oxide, diamond and aluminum nitride.

The two established materials are not interchangeable in every design. The roadmap identifies SiC as generally better suited to applications above 1.2 kV and GaN as highly competitive below 1.2 kV. Between 650 V and 1.2 kV, either technology may be a candidate, depending on the application and system requirements.

Choosing between SiC and GaN

SiC devices are associated with high breakdown voltage, thermal conductivity and operating-temperature capability. The roadmap also highlights their switching speed and potential for lower conduction and switching losses compared with silicon devices. These properties can make SiC relevant where voltage and thermal demands are significant.

GaN’s higher electron mobility supports high-frequency operation and lower losses in suitable applications. This can enable smaller devices and greater power density. For system designers, the practical question is not simply which semiconductor has the better headline properties, but which device best supports the required voltage, frequency, thermal conditions and overall power-conversion architecture.

These benefits need to be assessed at the system level. Device selection affects surrounding components and design choices, including packaging, gate drives and other power-electronics peripherals. A technology’s material advantages do not automatically translate into a better or more cost-effective system without appropriate integration.

Markets and adoption prospects

The roadmap identified applications including automotive power electronics, photovoltaic inverters and power supplies as areas where SiC and GaN progress was encouraging. It also pointed to slower adoption in traction applications, industrial motor drives and wind turbines, where further work was needed to address cost, reliability perceptions and system requirements.

Its market discussion cited forecasts published around 2018, including projections for substantial growth in SiC and GaN revenues by 2027. Those figures were projections at the time, not current market measurements. The broader point was that falling device prices and growth in applications such as electric vehicles and power supplies could expand demand, while the timing and scale of adoption would depend on manufacturing capacity and end-market development.

Four priorities for wider adoption

1. Reduce device and system costs

High material and manufacturing costs can limit adoption, particularly when silicon remains a viable alternative. The roadmap emphasizes lowering the cost per ampere of devices and modules, supporting vertically integrated fabrication, and encouraging early-adopter, high-volume applications. It also calls for open SiC and GaN foundries as a way to support higher-volume manufacturing.

2. Demonstrate reliability and quality

Industrial users need confidence that devices, modules and complete systems will perform reliably in their intended environments. Priorities include investigating degradation and failure mechanisms, building open reliability-data resources, developing the ability to conduct relevant AEC-Q and JEDEC testing, and establishing standards tailored to wide bandgap power electronics.

3. Connect device capability to application performance

Near-term projects can help demonstrate where wide bandgap devices provide system-level advantages. The roadmap recommends supporting industry-led pathways to commercialization and promoting reference designs, advanced gate drives, modules and complementary technologies. These efforts can help integrators evaluate devices in a complete design rather than in isolation.

4. Strengthen the ecosystem

Adoption also depends on coordination among semiconductor suppliers, equipment manufacturers, end users, universities and national laboratories. The roadmap identifies shared communication channels, access to devices for evaluation, workforce training and ongoing attention to both core technologies and longer-term applications as ecosystem priorities.

What this means for engineering teams

For engineers assessing a SiC or GaN design, start with the application’s operating conditions and system-level objectives. Compare voltage range, switching frequency, thermal demands and potential losses, then consider device cost, packaging and the maturity of the supporting design ecosystem. Where evidence is limited for a particular use case, reliability testing and a clear evaluation plan are important parts of technology selection.

Plant managers and operations leaders should likewise look beyond the semiconductor itself. The relevant decision is whether a complete power-conversion solution meets operational and economic requirements—not whether a device has an advantage in isolation.

Conclusion

SiC and GaN expand the options available to power-electronics designers, with distinct strengths across voltage and frequency ranges. Wider use will depend on more than device performance: manufacturers and the broader industry must address cost, reliability, packaging, standards and access to manufacturing. For automation and power-system teams, careful application-level evaluation is the practical route to identifying where wide bandgap technology can provide a meaningful advantage.

Access Official Technical PDF

About The Author