Designing a transmitter for wireless power transfer involves more than driving a coil. The system must control switching power electronics, measure electrical conditions, match impedance to the load and respond to unsafe states. A wireless power controller can bring key analog and timing functions together, providing an MCU with the measurements and control interfaces needed to manage those tasks.
Voltraware’s VW8000, also called Volta, is a transmitter-side analog front end implemented as a 68-pin eQFN ASIC. It combines wireless charging technology IP with supporting mixed-signal functions, programmable registers and non-volatile memory for calibration. Paired with an MCU—and an ADC for processing conditioned analog signals—the device is intended to simplify several design-critical parts of a wireless power system.
What a wireless power controller does
Most power delivery electronics use switching: transistors turn on and off in carefully managed sequences to provide a suitable output to a load. In a wireless power transmitter, this involves controlling both the DC supply stage and the power amplifier or RF inverter that drives the transmit coil.
Efficient operation also depends on understanding the electrical relationship between the transmitter and its load. Measuring current, voltage, phase and impedance gives the control system information it can use to adjust power delivery. Volta is designed to acquire and condition these signals, then make selected analog outputs available to an MCU for digital signal processing.
The device combines an eight-input, 16-channel analog acquisition and conditioning system with six PWM generators: two high-resolution and four standard-resolution. The MCU accesses control and status registers over SPI. This division lets the ASIC handle signal and timing functions while the MCU makes system-level decisions using measured operating parameters.
Signal conditioning, PWM and system control
Volta’s analog front end supports single-ended and differential signal conditioning and multiplexing. A programmable finite state machine selects signals for presentation to the MCU’s ADC, which accepts inputs up to 3.3 V. By handling signal selection within the controller, the design can reduce the MCU’s direct acquisition overhead.
Its PWM resources serve several roles in the transmitter. The high-resolution channels can drive the buck/boost converter and the Class D/E power amplifier, while standard-resolution channels can be used for functions such as fan or LED control. The high-resolution PWM provides 12 ns steps, with 17 additional 700 ps steps for fine adjustment.
Other interfaces and measurement functions include:
- SPI control and status access, plus digital interrupt and synchronization signals.
- Sixteen 5 V GPIOs and four 3.3 V GPIOs, controlled over SPI; the 3.3 V GPIOs are not 5 V compatible.
- A DC current shunt monitor and voltage-sense amplifiers for VPOW and VBUS.
- Peak detectors and isolated loop-current detection amplifiers, with support for external Rogowski coils or current transformers.
- Two single-ended temperature-sensor buffers, with ADC conversion and correction handled by the MCU.
The controller also includes an LDO to power an MCU at 3.3 V, along with integrated LDO/buck conversion for specified 5.0 V, 3.3 V and 1.8 V supply domains. Non-volatile memory supports IC trimming and stores system calibration constants for MCU algorithms.
Impedance matching and foreign object detection
The transmitter power path begins with an AC-to-DC supply. A buck/boost converter sets the DC level required by the power amplifier, and the amplifier converts that DC into AC to drive the transmit coil. Between the amplifier and coil, an impedance-matching network uses reactive components to transform the load reflected back to the amplifier.
Because the effective load affects power transfer, the system needs measurements that help characterize the matching network and coil. Volta provides two channels of four quadrature-phase mixers for precise impedance and phase measurement. The resulting data can support adaptive impedance tuning: the system can use measured conditions to guide adjustments to the matching behavior.
The same mixer measurements also feed the controller’s foreign object detection function, which uses impedance information to determine whether the load is normal or a foreign object. This links measurement and protection: the controller supplies data for system decisions rather than treating power delivery as an open-loop switching task.
Safety logic and timing architecture
Volta includes two Pin Safety Logic blocks, each associated with a PWM channel for the buck/boost converter or power amplifier. These blocks provide an interface between the internal PWM signals and external power stages. They can define PWM output polarity, inhibit a driver, limit power and establish predefined safe operating states.
Safety logic can compare monitored analog signals against configured thresholds without waiting for MCU intervention. The thresholds are digitally set and converted to analog levels through a DAC; programmable comparators provide additional threshold monitoring. This hardware path is intended to support automatic regulation and protection when monitored conditions reach configured limits.
A PLL multi-phase delay-locked loop and crystal reference provide a 6.78 MHz clock for the resonant magnetic field and an 81.36 MHz clock for PWM operation. The architecture also makes 17 delay taps available for fine control of the high-resolution PWM signals.
Integration considerations for system designers
Volta is a controller and analog front end, not a complete wireless power transmitter. The broader design still includes the AC-to-DC converter, buck/boost stage, power amplifier, matching network, transmit coil and MCU. For systems that require out-of-band communication, such as A4WP implementations, Bluetooth Low Energy and an appropriate protocol stack are also required.
The device is described as deployable across A4WP classes, with compatible systems built to support A4WP, PMA and WPC. Integrators should assess the required standard, power-stage design, sensing approach, MCU processing and protection behavior as parts of one system rather than assuming the controller alone determines compatibility or performance.
Conclusion
A wireless power controller can reduce the separation between transmitter measurements, switching control and protection. Volta brings signal conditioning, PWM generation, impedance and phase measurement, configurable safety logic and calibration support into one ASIC, while relying on an MCU for digital processing and system management. For engineers and integrators, the practical value lies in coordinating these functions within the transmitter architecture—and validating how the controller’s interfaces and protection features fit the specific power stages, load and communication requirements.