Access Official Technical PDF

Share Summary:LinkedInEmail

The 2SB649 transistor and its 2SB649A variant are silicon PNP devices specified for low-frequency power amplifier applications, used as a complementary pair with the NPN 2SD669/A. For engineers evaluating a legacy circuit or designing a replacement stage, the key considerations are the difference in collector-emitter voltage rating, the operating point behind the gain specification, and the relationship between power dissipation and temperature.

2SB649 and 2SB649A: key differences

The two versions share several headline ratings: collector-to-base voltage of –180 V, emitter-to-base voltage of –5 V, continuous collector current of –1.5 A, peak collector current of –3 A, and a maximum junction temperature of 150°C. Their primary stated voltage difference is collector-to-emitter breakdown voltage. The 2SB649 is rated at –120 V, while the 2SB649A is rated at –160 V.

That difference can matter when selecting a device for a circuit with higher collector-emitter voltage. It does not, by itself, establish suitability for every operating condition: current, power, temperature and safe operating area must also be checked. The negative signs reflect the PNP polarity and the datasheet’s voltage and current conventions.

Interpreting gain and electrical characteristics

The datasheet specifies DC current transfer ratio, hFE, under defined test conditions. At VCE = –5 V and IC = –150 mA, the 2SB649 has a listed range of 60 to 320, while the 2SB649A is listed at 60 to 200. Devices are grouped by gain band, so the exact range depends on the marked group. At IC = –500 mA, the listed minimum hFE is 30 for both devices; this entry is identified as a pulse test.

These values are not interchangeable with a guaranteed gain value at every point in a working circuit. Use the test conditions as a reference, and design the driver stage with the specified limits in mind rather than assuming a typical gain. The datasheet also gives a maximum collector-to-emitter saturation voltage of –1 V at IC = –500 mA and IB = –50 mA, and a maximum base-to-emitter voltage of –1.5 V at IC = –150 mA and VCE = –5 V.

For frequency-related checks, the listed typical gain-bandwidth product is 140 MHz at VCE = –5 V and IC = –150 mA. Typical collector output capacitance is 27 pF at VCB = –10 V, with emitter current zero and a test frequency of 1 MHz. These are test-point values; they should be considered in the context of the intended circuit and operating conditions.

Power dissipation, temperature and safe operating area

Thermal limits are central to applying this transistor. The absolute maximum ratings list collector power dissipation as 1 W and give a separate 20 W rating at a case temperature of 25°C. The distinction matters: the higher figure is tied to a controlled case temperature and is not a general allowance for an unheatsinked device. The maximum collector dissipation curve shows that allowable dissipation decreases as case temperature rises.

The junction temperature limit is 150°C, and the storage temperature range is –55°C to +150°C. In a real assembly, designers must account for heat flow from the junction through the package and mounting arrangement, as well as the ambient and case temperatures. Staying below an individual voltage or current maximum does not ensure that the device remains within its thermal limits.

The safe operating area chart adds another important constraint by showing allowable combinations of collector current and collector-emitter voltage for DC operation at a case temperature of 25°C. Its boundary limits the combinations that can be used together; the maximum current rating should not be treated as permissible at every voltage. Check the chart against the circuit’s expected operating point and fault or transient conditions.

Package pinout and practical design checks

The devices use a modified TO-126 package. The datasheet’s terminal outline identifies the leads, in order, as:

  • Pin 1: emitter
  • Pin 2: collector
  • Pin 3: base

Confirm the package orientation and pin numbering against the actual component and board layout before assembly, particularly when working from an existing footprint or substituting a device. The datasheet also notes that product specifications may change, so the applicable product documentation should be confirmed before final design or use.

For a design review, verify the required collector-emitter voltage, current and gain at the intended operating point; check saturation and drive requirements; and assess dissipation against case temperature and the safe operating area. Also account for the complementary 2SD669/A stage as part of the amplifier design rather than evaluating the PNP device in isolation.

Conclusion

The 2SB649 and 2SB649A provide a documented PNP option for low-frequency power amplification with the complementary 2SD669/A. Their most notable distinction is the 2SB649A’s higher collector-emitter breakdown rating, while their gain ranges and thermal constraints still require careful attention. Using the specified test conditions, package pinout, dissipation limits and safe operating area together helps engineers assess whether either device fits the circuit’s actual requirements.

Access Official Technical PDF

About The Author