A 60 GHz wireless link must handle signals at millimeter-wave frequencies, where photonic techniques can offer a flexible way to generate and tune electrical signals. A demonstrated hybrid architecture brings photonics and electronics together at the receiver: a photonic integrated circuit (PIC) generates the local-oscillator signal for an electronic mixer, which converts an incoming 64.5 GHz carrier to an intermediate frequency. The three-metre link carried 1 Gbps on-off keying (OOK) data, and offline processing recovered the transmitted sequence with zero errors in 100,000 bits.
Why combine photonics and electronic mixing?
Millimeter-wave (mmWave) systems use frequencies from 30 to 300 GHz. The 60 GHz band is of interest for wireless communications because it includes 7 GHz of unlicensed spectrum in many countries. At these frequencies, the available bandwidth can support high data rates, while small antenna dimensions can help enable multiple-input multiple-output (MIMO) arrangements.
Generating and receiving mmWave signals can involve either electronic or photonic approaches. A uni-traveling carrier photodiode (UTC-PD) can produce high-frequency electrical signals through optical heterodyning: two optical tones with different frequencies are combined, and their frequency difference appears as an electrical signal at the photodiode. UTC-PDs are valued for mmWave generation, but their use as optoelectronic mixers can involve substantial frequency-conversion loss.
An electronic mixer offers a different trade-off. It can provide lower conversion loss, but typically needs a high-frequency electronic local oscillator (LO), which can be costly and limit frequency agility. The hybrid receiver addresses this by using a UTC-PD to generate the LO optically and an electronic mixer to perform the down-conversion. In principle, this combines photonic tuning with electronic mixing.
How the 60 GHz wireless link works
Photonic LO generation at the receiver
The receiver PIC integrates two UTC-PDs, two distributed feedback (DFB) lasers, semiconductor optical amplifiers (SOAs), and other optical components. For the experiment, the PIC produced two optical tones whose spacing generated an electrical heterodyne signal near 52 GHz. That signal drove the LO port of a double-balanced electronic mixer.
The PIC’s laser could operate in multiple optical modes. The selected operating regime produced a principal tone spacing of about 52 GHz, suitable for the receiver’s mixer. During PIC characterization, the electrical heterodyne signal measured at 51.9 GHz had a peak power of -21 dBm at the analyzer; after accounting for cable and bias-tee losses, its estimated power at the probe input was -10.7 dBm. This step checked that the integrated photonic source could provide an LO at the required frequency.
Transmitting and down-converting the data
At the transmitter, two external-cavity lasers generated optical tones separated by 0.52 nm, corresponding to a 64.5 GHz electrical signal. A Mach-Zehnder modulator placed 1 Gbps OOK data on one optical tone. The tones were combined, amplified, and sent to a UTC-PD, which converted their frequency difference into the modulated mmWave signal.
A power amplifier and variable attenuator conditioned the electrical signal before transmission through a 24 dBi gain parabolic antenna. The receiving antenna, also rated at 24 dBi, collected the signal three metres away. A low-noise amplifier then boosted it before it reached the electronic mixer.
With a roughly 52 GHz LO from the PIC, the mixer translated the received 64.5 GHz signal to a 12.5 GHz intermediate frequency (IF). The PIC-driven mixer subsystem had a measured conversion loss of 23 dB under the characterization setup. The IF signal was captured by a real-time oscilloscope for offline digital signal processing.
Data recovery and measured results
Processing included signal filtering, digital down-conversion to baseband, channel equalization using the constant modulus algorithm (CMA), and envelope detection. The recovered data showed an open eye diagram. Comparing transmitted and received bits found zero errors across the 100,000-bit waveform captured for analysis. This result describes the tested sequence; it should not be interpreted as a general error-rate guarantee for other operating conditions.
A second mixing product, associated with the laser’s multi-mode operation, appeared at 9 GHz. It did not prevent recovery of the wanted data because digital filtering removed it. The oscilloscope also produced spectral lines at multiples of 5 GHz, which were identified as instrument clock signals rather than components of the received IF signal.
Practical implications for system design
The demonstration shows how a photonic LO source can be paired with an electronic mixer in a mmWave receiver. For system integrators, the key design point is the division of work: the PIC provides an optically generated, tunable LO, while the electronic mixer performs RF-to-IF conversion. The approach therefore offers an alternative to relying entirely on photonic or electronic components.
There are important boundaries to the result. The wireless transmission was demonstrated over three metres in a laboratory setup. The authors noted that removing a 3 dB transmitter attenuation could correspond to a distance of four metres, but that was not the demonstrated transmission distance. The result establishes feasibility, not performance across different ranges, environments, or network configurations.
Conclusion
A 60 GHz wireless link using a photonic integrated circuit to drive an electronic mixer can recover 1 Gbps OOK data after a 64.5 GHz signal is down-converted to a 12.5 GHz IF. For engineers evaluating hybrid mmWave architectures, the practical takeaway is that photonic LO generation and electronic mixing can be integrated into one receiver chain. Further system decisions should account for the measured conversion loss and the specific conditions under which the link was tested.