The SSI2144 voltage controlled filter is a four-pole analog filter IC intended for subtractive synthesis and related signal-processing designs. It reprises the circuit of the SSM2044, using Dave Rossum’s improved ladder topology, while incorporating design refinements and modern process technology. For engineers integrating an analog filter into a synthesizer or other electronic music system, its appeal lies in combining a familiar tonal character with improved resonance consistency, low control feedthrough and a wide frequency sweep.
Architecture and key features
The SSI2144 operates as a four-pole lowpass filter. Its internal stages shape the signal while a frequency-control input sets the cutoff, and an on-chip resonance circuit provides feedback around the filter. The device accepts differential signal inputs, which can simplify connections when combining sources such as two oscillators.
Compared with the SSM2044 circuit it reprises, the SSI2144 improves the Q-control circuit so that the current applied at the resonance input is more accurately reflected in the feedback amplifier. This reduces process-dependent variation in resonance behavior. Other stated design benefits include lower noise, improved control feedthrough and more consistent unit-to-unit resonance performance. The device also supports supply voltages from ±4V to ±16V and uses a 16-lead SSOP package with relatively few external components.
The specified frequency sweep range is typically 20,000:1, with a minimum of 10,000:1. Frequency control is exponential: changes in control voltage produce corresponding changes in cutoff frequency. The control sensitivity is specified at approximately -19mV per octave under the stated conditions.
Frequency control and signal inputs
In a typical application, a control summer combines sources such as a panel control, an envelope generator or a low-frequency oscillator before driving the SSI2144 frequency-control pin. The control summer and input attenuation should be designed so the control pin’s voltage range matches the intended cutoff sweep. In the example circuit using ±12V supplies, a ±90mV swing at the frequency-control pin corresponds to a 1,000:1 sweep range.
Designers should account for offset as well as modulation depth. In polyphonic systems, a frequency-offset adjustment can help align cutoff across voices. It is also useful in programmable systems where a given control voltage is expected to produce repeatable cutoff behavior.
The signal inputs are differential, but the example application attenuates the SIG IN− path by 3dB to avoid cancellation when the inputs carry in-phase signals. If only one input is used, the unused input should be connected to ground through a 200-ohm resistor. The nominal differential input signal level is ±20mV, and clipping occurs at approximately ±50mV. External resistor values in the application circuit scale higher-level signals to the appropriate input range.
Understanding resonance and Q control
The Q control is a current-input summing node held at ground potential. At zero control current, resonance is at its minimum. Increasing current strengthens feedback, raising the response peak around cutoff while reducing gain at DC and below cutoff. The filter maintains an approximate 24dB-per-octave rolloff at higher frequencies.
When feedback exceeds 12dB, loop gain at cutoff exceeds unity and the filter oscillates, producing a sinewave at the cutoff frequency. This behavior can be useful when the filter is also intended to act as a tone source. The datasheet identifies approximately 400µA as the current associated with oscillation, though the exact circuit behavior depends on the implementation.
Resonance does not increase linearly with Q-control current: the response is relatively gradual at lower currents and rises more steeply as oscillation approaches. For a more usable control feel, the recommended circuit uses a reverse-audio-taper potentiometer. This taper compensates for the changing response slope, giving more adjustment resolution through the useful resonance range.
Practical integration considerations
Very low cutoff frequencies
When the frequency-control voltage rises above approximately 175mV, the filter can behave undesirably: its output stage common-mode voltage may drop, signal transmission can stop, and the output may move to an unrelated fixed voltage. Normal operation resumes as the control voltage falls to roughly 135mV, potentially with an audible transient. The exact transition points can vary between parts or batches.
For applications requiring sub-audio cutoff frequencies, the datasheet describes a network connected to both C4 pins using matched low-leakage diodes or diode-connected transistors, together with a diode reference and a resistor to the negative supply. This arrangement helps prevent the output-stage common-mode voltage from dropping, allowing filter performance to degrade more gradually at extremely low cutoff settings.
Managing passband attenuation at high resonance
As Q increases, the SSI2144’s negative-feedback behavior reduces passband gain. Some designs may want to retain this characteristic; others may need to compensate for it. The documented alternatives use an external Q VCA built around one-half of an LM13700 transconductance amplifier. By increasing the input signal as Q rises, these circuits can offset the DC gain reduction and maintain more nearly constant gain.
The non-linearized and linearized versions use different component values and control-current ranges. The non-linearized circuit is described as suitable when retaining the vintage SSM2044-style response is desired, while the linearized version uses the LM13700’s linearizing diodes to minimize distortion in the Q VCA. These are application-specific circuit choices, not changes to the SSI2144’s internal filter behavior.
Design takeaway
The SSI2144 provides a well-defined set of building blocks for a four-pole analog lowpass filter: exponential voltage control, differential inputs and current-controlled resonance. Successful integration depends on matching the external control circuitry to the desired sweep, setting up offsets where repeatability matters, and understanding how Q affects both resonance and low-frequency gain. Designs that extend into sub-audio cutoff ranges or require stable passband level at high resonance should also consider the additional circuits described for those conditions.