Access Official Technical PDF

Share Summary:LinkedInEmail

Glass micromachining can enable compact components and tools for applications that benefit from glass’s optical and radio-frequency transparency, chemical inertness, and mechanical and thermal properties. But producing high-precision glass parts in small batches—especially when each part has a different geometry—presents a manufacturing challenge. Glass is hard and brittle, while conventional workflows can require lengthy calibration, specialized fixtures and substantial setup for each design.

Spark Assisted Chemical Engraving (SACE) offers a hybrid approach to machining glass. Research into the process has focused on adapting it from repeatable production toward mass personalization: making changing, low-volume part designs without allowing the associated preparation work to dominate the workflow. The approach combines process modeling with in-situ tooling and rapid prototyping to address key sources of manufacturing overhead.

Why personalized glass parts are difficult to produce

In mass personalization, production may involve small batches—or even a batch size of one—with geometry that changes from part to part. The manufacturing process therefore needs to accommodate design variation without relying on extensive part-specific preparation. For precision glass work, several activities can make that difficult:

  • Process planning: Operators need a reliable way to connect machining inputs with the desired cut or milled feature.
  • Alignment and calibration: Establishing the relationship between the tool and workpiece, and correcting tool run-out, can require significant setup.
  • Workholding: A custom fixture may be needed to clamp a glass workpiece securely and accurately.
  • Tooling and lead time: Dedicated tooling can add indirect cost and delay, particularly when part designs change frequently.

These barriers matter because reducing the time spent machining a feature is only one part of improving production economics. A flexible process also needs to reduce the preparation and support work required to make each new design manufacturable.

How SACE machining works

SACE is a hybrid electrochemical and thermal process. The glass workpiece is immersed in an alkaline electrolyte, typically sodium hydroxide or potassium hydroxide. A voltage above a critical level is applied between the tool electrode and a counter-electrode. Sparking develops around the tool, locally promoting chemical etching of the glass.

Because material removal is localized near the tool, SACE can be used for operations including drilling, cutting and milling on the same machining setup. This versatility is relevant to personalized components: different feature types can be produced without necessarily changing to a separate machining technology for each operation.

Glass remains challenging to machine, however. Its hardness and brittleness make smooth surfaces and high-aspect-ratio features difficult to achieve efficiently. SACE can address some of these difficulties, but using the process for precision, design-variable production requires more than the machining principle itself. Process planning, alignment and workholding must also be made more adaptable.

Making glass micromachining more adaptable

Relating process inputs to machining outcomes

A central development is an empirically validated model for SACE cutting and milling. The purpose is to relate machining inputs to the intended outcome, helping translate a design into suitable machining instructions. In practical terms, this supports automation across the workflow: from the desired geometry to machinable code that includes the information needed to execute the operation.

Models do not remove the need for process control. They provide a structured basis for selecting and planning machining conditions, reducing reliance on repeated trial-and-error calibration when a part geometry changes. This is particularly important in personalized production, where a setup method that works for a long, unchanged run may be inefficient for a succession of distinct designs.

Reducing alignment and tooling overhead

The developed approach also addresses setup and workholding. In-situ tool fabrication is used to prepare the required tool within the machining workflow, including steps to correct tool-to-substrate misalignment and reduce tool diameter and run-out. This targets the time and effort otherwise associated with extensive tool adjustment.

For workholding, the approach uses low-cost rapid prototyping to make the needed tooling. Rather than depending on a dedicated, externally produced fixture for every glass design, in-situ fabrication can help make part-specific support more compatible with short lead times. The aim is to lower indirect machining costs as well as the delay between a design change and production.

Applications beyond the glass component

The research demonstrated the approach through applications in microtechnology. One was the fabrication of glass imprint templates for hot embossing. The glass templates were used to transfer microfeatures to polymer substrates, including polycarbonate. In this workflow, the machined glass part serves as a tool for producing other patterned components.

A second application was the manufacture of glass dies for micro-forming metal parts. These examples show how precision glass machining can support downstream manufacturing processes, not only the production of finished glass devices. SACE was also used in work on packaged glass devices, where machining and bonding were combined in a workflow intended to eliminate a process step between micromachining and die singulation.

These demonstrations illustrate the potential value of a flexible process chain: a glass feature may be the final product, a template for replication, or a tool used to form another material. The appropriate workflow depends on the part and its intended use.

Practical considerations for manufacturers

For engineers and system integrators assessing SACE, the key point is that flexibility comes from coordinating several elements rather than relying on a single machining capability. A practical implementation needs a suitable process model, a way to prepare and align tools, stable workholding, and a digital path from design geometry to machining instructions.

The approach is most relevant where glass feature requirements vary and conventional preparation—such as repeated calibration or dedicated fixture production—would create significant overhead. It does not remove the need to validate machining quality or determine appropriate process conditions for a specific application. Instead, it provides methods for making those activities more repeatable and integrated into the manufacturing workflow.

Conclusion

SACE expands the options for glass micromachining by combining localized electrochemical and thermal material removal with developments aimed at reducing preparation effort. Empirical process modeling, in-situ tooling and rapid prototyping address important barriers to producing high-precision parts with changing geometries. For manufacturers considering personalized glass components, the practical implication is to evaluate the entire workflow—from design and workholding through machining and downstream use—rather than focusing on cutting performance alone.

Access Official Technical PDF

About The Author