Access Official Technical PDF

Share Summary:LinkedInEmail

A MEMS VCSEL on silicon can combine a tunable laser cavity with fabrication approaches suited to silicon-based integration. In the demonstrated design, a movable high-contrast grating mirror is built on a silicon-on-insulator substrate, while bonded indium phosphide provides the quantum-well gain material. A deposited dielectric mirror completes the laser. The architecture targets several familiar challenges in tunable vertical-cavity surface-emitting lasers: protecting the moving MEMS element, widening the useful tuning range, and keeping the laser cavity short enough to support a large free spectral range.

These design considerations matter in applications that use swept laser sources, including optical coherence tomography (OCT). The work demonstrates a 40 nm tuning range under direct-current actuation and mechanical resonance at 2.46 MHz, with approximately 15–20 nm of tuning reported during resonant alternating-current actuation. Those results illustrate how the mechanical, optical, and fabrication choices interact; they are not, by themselves, a complete system-level performance specification.

Why change the conventional MEMS VCSEL layout?

In many established MEMS VCSEL designs, the bottom mirror and active laser material are formed together, and a suspended top mirror provides the tuning motion. Because the movable structure is exposed, it requires careful handling and external packaging for protection. Environmental changes, including humidity and temperature, can also create risks such as condensation that may damage the MEMS element.

Electrostatic actuation introduces another constraint. The attractive force typically pulls the movable mirror in one direction, and travel must be limited to avoid electrostatic snap-in. That limit restricts how much the mirror can move within a given gap. Increasing the gap can make more travel possible, but also lengthens the optical cavity. A longer cavity reduces the free spectral range, creating a trade-off between tuning travel and cavity properties that can constrain mode-hop-free wavelength coverage.

How the MEMS VCSEL on silicon is structured

The alternative design places the high-contrast grating (HCG) bottom mirror on a MEMS frame defined in the silicon device layer of a silicon-on-insulator (SOI) wafer. The HCG moves; the active material and top mirror remain stationary. An indium phosphide layer containing quantum wells is bonded above the silicon structure, and a dielectric distributed Bragg reflector (DBR) is deposited as the top mirror.

The bonded active layer and top mirror also enclose the MEMS cavity. This sealed arrangement protects the moving element and gives designers a way to control the cavity environment. For example, partial vacuum or a controlled gas pressure can be used to adjust mechanical damping. The architecture also allows the HCG to be actuated from either a top or bottom electrode. Operating with the bottom electrode alone creates a pull-away arrangement that separates the actuation gap from the laser cavity length: the mirror can sit close to the active region while the mechanical gap is set independently.

That separation is significant because it addresses the tuning-range versus free-spectral-range trade-off at the level of the device layout. It also creates the possibility of bidirectional mirror motion, although the demonstrated device achieved only limited tuning in one direction. The reported 40 nm DC tuning range should therefore be read alongside the authors’ note that gain bandwidth and heat extraction remain factors in expanding the usable range.

Fabrication combines silicon processing and wafer bonding

The process begins with an SOI wafer whose silicon device layer is patterned to create the HCG and its surrounding MEMS frame. A silicon dioxide layer defines the gap and provides the bonding interface. Since direct bonding requires a very smooth surface, the process uses a two-step oxide and glass deposition followed by annealing to improve surface roughness. The MEMS structure is then released using dry and wet etching, with critical-point drying used to avoid damage during release.

The prepared silicon wafer is directly bonded to an InP wafer containing the quantum-well active region, using aluminum oxide as an intermediate layer. After bonding, the InP substrate is removed to leave the active layers. Contact openings and metal contacts are added, followed by deposition of the TiO2/SiO2 DBR. In this approach, the two mirrors are defined using silicon processing rather than relying on challenging epitaxial growth for both mirrors. The process also places key steps—including patterning, active-material growth, and bonding—before later contact and mirror-deposition steps.

What the device characterization shows

The fabricated laser was optically pumped, with a 976 nm pump used for most characterization. The reported threshold input power delivered to the chip was approximately 5.5 mW, and the maximum measured output power was 0.1 mW. A measured spectrum showed single-mode emission at 1564 nm with a side-mode suppression ratio greater than 55 dB. These measurements characterize the optically pumped prototype; they should not be interpreted as results for an electrically injected production device.

Applying voltage between the MEMS silicon layer and the silicon substrate shifted the emission toward longer wavelengths. Applying voltage between the bonded InP layer and the MEMS layer produced a shift in the opposite direction, demonstrating some bidirectional tuning, though the range in that direction was limited. Under resonant AC actuation at 2.46 MHz, the tuning curve covered roughly 15–20 nm. Resonant operation increased the tuning range compared with the AC drive away from resonance, while DC bias shifted the tuning curve and affected its bandwidth.

Thermal behavior is another design consideration. Pump absorption heats the active region, changing the refractive index and shifting the lasing wavelength. The reported wavelength response depended both on substrate temperature and on pump power, with local pump-related heating having a strong influence. For system designers, this highlights the importance of treating heat extraction and operating conditions as part of wavelength-control design rather than as separate packaging concerns.

Practical implications for photonic integration

The work demonstrates a device architecture that combines silicon MEMS fabrication, bonded III-V gain material, and a sealed movable mirror. Its practical value lies in the design options it opens: environmental protection for the MEMS, adjustment of mechanical damping, and partial decoupling of tuning travel from laser-cavity length. These features make the approach relevant to development of compact swept-source photonics, including sources intended for OCT.

Further development would need to address the limits identified in the device results. A wider active-layer gain bandwidth and improved heat extraction could support a broader useful tuning range, while tighter control of oxide deposition could improve wavelength repeatability between devices. The central engineering lesson is that tuning performance depends on coordinated optical, mechanical, thermal, and process design. A silicon-based MEMS VCSEL offers a route to combine those elements in an integration-oriented structure, but application-level performance must be validated in the complete source and system.

Access Official Technical PDF

About The Author