Access Official Technical PDF

Share Summary:LinkedInEmail

Micro part handling presents a distinct challenge for industrial automation: components are small enough that minor positioning errors can disrupt pickup, placement or assembly. Gravity may be too weak to release a part reliably from a tool, while excessive gripping force can damage it. A production-cell design developed for micro-injection molding addresses these constraints by combining an XYZ Cartesian table, a vacuum gripper, visual inspection and PLC-based coordination.

The approach is relevant to manufacturers integrating micro-injected component production with inspection, assembly and palletizing. Rather than treating manipulation as an isolated pick-and-place task, it connects the handling system to the wider cell and its material flow.

Why micro part handling needs a different approach

Micro parts can have dimensions or features in the micrometer range. At this scale, both catching and releasing a component require attention. The gripper needs enough force to retain the part without damaging it, but the release action must also overcome adhesion between the component and the end effector. Because gravity contributes little to releasing very small parts, simply opening the gripper may not be sufficient.

Gripper selection also affects repeatability and integration. Passive gripping methods depend on contact and surface properties, which can make results less consistent. Active microgrippers can use actuators such as piezoelectric or pneumatic elements, but these approaches have trade-offs in cost or precision. Vacuum systems offer another option for pick-and-place operations, provided their pickup and release behavior is managed appropriately.

Micro part handling with an XYZ Cartesian table

The cell uses a Cartesian table with linear X, Y and Z motion. Its travel dimensions are 450 mm on the X axis and 150 mm on both the Y and Z axes. The reported position repeatability is 0.02 mm, with a maximum speed of 800 mm/s. This arrangement provides a comparatively straightforward way to position the end effector along defined linear paths.

Cartesian motion is a practical fit for a cell in which components are presented in trays and operations take place at known locations. Unlike an articulated robot, the table is limited to linear movements, but it can be integrated into the cell’s handling sequence without requiring the more specialized pick-and-place equipment considered for the application. The choice is therefore tied to the required motion, accuracy and production-cell integration—not simply to robot type.

Designing the gripper for pickup and release

The end effector has three nozzles. All three can be used to handle a cogwheel, supporting more precise and secure pickup; a single nozzle is used for a micro part or pin. Each nozzle has an internal diameter of 0.5 mm. A spring helps prevent the nozzle from applying damaging force when it contacts a component.

The vacuum system uses the cell’s typical 6 bar pressure and has two vacuum generators. One controls vacuum for the nozzle used with micro parts and pins. The other serves the remaining two nozzles used for cogwheels. The generator for the smaller components can also produce a blow to assist release, compensating for the limited role of gravity at this scale.

A vacustat checks whether a part has been picked up. The system compares the measured negative pressure with a defined threshold; if the pressure does not reach the required condition after pickup, the part is treated as not captured. This provides a check within the handling sequence rather than relying only on the commanded movement.

Coordinating inspection, the PLC and the robot

The manipulation system is part of a larger production cell for micro-injected parts. The cell includes production, palletizing, visual inspection, selection and assembly zones. The vision system inspects trays and identifies defective components. Its report is processed by a PLC, which communicates the relevant tray positions to the XYZ table for removal.

The PLC also acts as an intermediary between the table and the robot arm. The robot controls the wider cell and tells the table which operation to perform, such as moving to a safe position or removing defects. In turn, the table signals when it needs trays and when the robot can collect a tray after an operation is complete. This division of responsibilities links local positioning tasks to the cell’s broader sequencing.

Assembly and defect-removal sequences

For assembly, the table works with trays of micro parts, cogwheels and pins. It places pins into four holes in each cogwheel, then positions micro parts on top of the pins. Because the quantity of pins and micro parts in a tray is not enough to complete all cogwheels, the table requests additional trays as required. When assembly is complete, it signals that the robot can collect the tray.

For defect removal, the PLC receives the inspection report and sends the defective-part positions to the table. The robot supplies a tray containing defective parts and another containing good parts. The table removes the identified defects and replaces them with good components, requesting another tray when the available supply is exhausted.

Managing alignment and process reliability

Testing identified tray misalignment as a source of repeatability problems. Even small offsets matter when the parts—and particularly the pins—are small. Correcting tray alignment addressed part of the issue, while using visual information to help adjust the final gripper position was under consideration. A pressure regulator was also being implemented to limit the blow used to release micro parts and pins.

These findings underline a practical point for integrators: accurate axis positioning alone does not guarantee reliable microassembly. Tray presentation, pickup confirmation, controlled release and communication between inspection, PLC and motion control all contribute to the result.

Practical implications for automation teams

A micro part handling cell should be designed around the behavior of the component as well as the motion system. The described arrangement combines linear Cartesian positioning with vacuum pickup, a release blow, pressure-based pickup detection and inspection-guided defect removal. Its modular coordination with a PLC and robot arm also connects manipulation tasks to the production cell.

For engineers and operations teams, the key is to validate the full sequence: how parts are presented, captured, transferred, released, inspected and replaced. Attention to alignment and pneumatic release control can be as important as selecting an appropriate robot. In microassembly, reliable handling comes from coordinating the tool, motion, sensing and cell logic around the limits imposed by very small components.

Access Official Technical PDF

About The Author