Access Official Technical PDF

Share Summary:LinkedInEmail

MIPS processor design offers a useful example of how processor architecture, RTL verification and ASIC implementation connect. A 32-bit implementation with a five-stage pipeline divides instruction execution into smaller steps, while its design flow moves from Verilog simulation and synthesis toward physical layout. For automation engineers and system designers, the work highlights a broader principle: functional correctness and physical performance are related, but they must be evaluated at different points in the implementation process.

MIPS processor design and the RISC approach

MIPS is based on reduced instruction set computing (RISC). Compared with architectures built around more complex instructions, RISC designs typically use a smaller instruction set, fixed instruction formats, general-purpose registers and a load-store model. In a load-store architecture, data is transferred between memory and registers by specific instructions; arithmetic and logic operations primarily use register operands.

This structure can simplify instruction decoding and datapath organization. It does not, by itself, guarantee a particular speed, area or power result. Those outcomes depend on the implementation, technology library, design constraints and physical realization. As in other IC designs, area, power and delay are coupled: improving one may require tradeoffs in the others.

How the five-stage pipeline works

A pipeline allows different instructions to occupy different processing stages at the same time. Instead of completing one instruction through every operation before beginning the next, the processor advances instructions through a sequence of stages. The described 32-bit MIPS architecture uses five:

  • Instruction fetch (IF): The program counter identifies the next instruction address, and instruction memory supplies that instruction. The program counter is updated to select the next address.
  • Instruction decode (ID): The processor interprets the instruction and obtains the required register operands. Control information is also prepared for later operations.
  • Execution (EX): The arithmetic logic unit (ALU) performs the required calculation. This stage also supports address calculations and branch-related operations described for the design.
  • Memory access (MEM): Load and store instructions use the calculated address to read from or write to data memory. For other instructions, the result proceeds toward write-back.
  • Write-back (WB): The result, including data returned from memory for a load, is written to the destination register.

As one instruction advances from fetch to decode and then execution, subsequent instructions can enter earlier stages. This overlap is the central benefit of pipelining: it increases the rate at which instructions can be processed when the design and instruction flow allow the stages to operate effectively. A pipeline does not mean that every individual instruction completes in one stage.

Verification before physical implementation

Before generating a physical layout, the processor’s behavior needs to be checked at the RTL level. In the reported implementation, Verilog code for the 32-bit processor was simulated using Cadence NC Launch. A testbench supplied a sequence of instructions to instruction memory so the design’s responses could be observed in simulation waveforms. The design schematic was also examined.

This functional verification step addresses a different question from physical design. Simulation checks whether the RTL behaves as intended for the test conditions; it does not establish that the final layout meets timing or power requirements. A testbench is therefore an important starting point, but its instruction sequences and checks need to be appropriate to the behaviors the design is expected to support.

From RTL synthesis to ASIC layout

After functional checks, synthesis translates the RTL description into a gate-level netlist using a specified standard-cell library. The reported flow uses Cadence RTL Compiler to generate the netlist and produce area, power and timing reports. These reports can be inspected by design hierarchy, including blocks such as the register file, ALU, control unit and data RAM.

The next step is physical implementation. Cadence SoC Encounter is used to create a layout from the netlist and design constraints. The described flow includes routing and clock distribution. Physical implementation matters because a logical netlist must be placed and connected on silicon; the resulting layout is then assessed for timing behavior.

Timing signoff analysis is described using the Tempus tool, with timing slack used to evaluate the design against its timing requirements. The paper reports that the Tempus timing-slack result was better than the result from Encounter’s timing debug analysis. Such tool outputs should be interpreted in the context of the constraints and analysis setup, rather than treated as interchangeable measures.

Reading area, power and delay results carefully

The paper reports area, power and delay figures for a 90 nm implementation: area of 54,956, power of 400,611 nW and delay of 1,048 ps. The area unit is printed as mm², but the paper does not provide enough context to independently verify that unit or reconcile it with the stated implementation. These figures should therefore be checked against the original reports and library assumptions before being used for comparison or planning.

More broadly, a meaningful comparison between implementations requires consistent definitions and conditions. Engineers should confirm the area metric, power-reporting assumptions, timing constraints, technology library and analysis stage. The paper describes optimization as an objective, but does not provide a baseline or enough comparative data to quantify an improvement.

Practical implications for design teams

The MIPS example shows why a complete ASIC workflow needs more than a functioning RTL model. Teams need to verify instruction behavior, synthesize against the intended cell library, implement the design physically and analyze timing after layout. They must also review how reports are generated and whether their units and assumptions support valid comparisons.

For engineers and technical decision-makers, the practical takeaway is to treat architecture, verification and physical design as connected but distinct tasks. A five-stage pipeline defines how work is organized; simulation tests functional behavior; and synthesis and physical implementation reveal the area, power and timing characteristics of a particular realization. Clear constraints, traceable reports and careful interpretation are essential to making sound implementation decisions.

Access Official Technical PDF

About The Author