The 2SC458 transistor and its related 2SC2308 are silicon NPN devices specified for low-frequency amplifier applications. Their datasheet provides useful information for engineers assessing a transistor for a discrete circuit, including voltage and current limits, gain characteristics, noise data and TO-92 package connections. Understanding how those figures relate to actual operating conditions is essential: absolute maximum ratings are limits, not recommended operating points.
2SC458 transistor and 2SC2308 overview
Both devices are identified as NPN epitaxial transistors. The listed application is low-frequency amplification, and the datasheet notes that they can form complementary pairs with the PNP devices 2SA1029 and 2SA1030. That pairing information can help when considering complementary circuit arrangements, but the required operating conditions still need to be checked against the specifications for every device in the design.
The two NPN models share several characteristics, but their voltage ratings differ. The 2SC458 has collector-to-base and collector-to-emitter voltage ratings of 30 V. For the 2SC2308, those ratings are 55 V and 50 V, respectively. Both list a 5 V emitter-to-base voltage rating, 100 mA collector current, and 200 mW collector power dissipation at an ambient temperature of 25°C.
Reading the transistor ratings correctly
Absolute maximum ratings describe boundaries that should not be exceeded. They are not a complete design specification and do not, by themselves, establish a safe continuous operating point. A circuit review should consider the combination of voltage, current, power dissipation and temperature—not just whether each individual value appears below its listed maximum.
- Collector current: The listed maximum is 100 mA for both devices. The intended circuit current should be determined from the amplifier design and kept within the applicable device limits.
- Collector power dissipation: The maximum rating is 200 mW at Ta = 25°C. The datasheet’s dissipation curve shows that the permitted collector dissipation decreases as ambient temperature rises, so the 25°C figure should not be treated as constant at higher temperatures.
- Temperature: The junction temperature limit is 150°C. The specified storage-temperature range is −55°C to +150°C; storage limits are not operating targets.
- Voltage: Check the appropriate collector-to-base, collector-to-emitter and emitter-to-base ratings for the circuit. The 2SC458 and 2SC2308 do not have identical collector voltage limits.
The datasheet also states that the devices should be used within guaranteed ranges and that thermal dissipation and installation conditions matter. For equipment where semiconductor failure could create a safety risk, the manufacturer advises incorporating system-level measures such as fail-safes. The document also says the product is not designed to be radiation resistant.
Gain and low-frequency amplifier characteristics
At the stated test condition of VCE = 12 V and IC = 2 mA, the DC current transfer ratio, hFE, is specified from 100 to 500 for the 2SC458 and from 100 to 320 for the 2SC2308. These are ranges rather than a single guaranteed gain value. The datasheet further groups parts by gain: grades B, C and D cover 100–200, 160–320 and 250–500 for the 2SC458. For the 2SC2308, grades B and C cover 100–200 and 160–320; no D grade is listed.
Other listed electrical characteristics can help with a more detailed assessment. At VCE = 12 V and IC = 2 mA, the typical base-to-emitter voltage is 0.67 V, with a maximum of 0.75 V, and the typical gain bandwidth product is 230 MHz. The collector-to-emitter saturation voltage is specified at up to 0.2 V under a test condition of IC = 10 mA and IB = 1 mA. These figures apply to their stated test conditions; they should not be assumed to hold unchanged at other bias points.
For noise evaluation, the datasheet gives a noise figure of 4 dB typical and 10 dB maximum at VCE = 6 V, IC = 0.1 mA, 1 kHz and a 500-ohm source resistance. Its accompanying plots show noise figure versus frequency and collector-to-emitter voltage under specified test conditions. This makes the data relevant when reviewing a low-level amplifier stage, but the plotted and tabulated results should be interpreted in the context of the circuit’s own source impedance, bias and signal frequency.
TO-92 package and pin connections
The devices are shown in a TO-92 package. The outline identifies the leads as emitter (pin 1), collector (pin 2) and base (pin 3). Before assembly or replacement, confirm the orientation against the applicable package drawing and the component’s actual lead arrangement. Correctly identifying the base, collector and emitter is a basic but important step when integrating a transistor into a board or troubleshooting an existing circuit.
Practical checks before selecting a device
When evaluating a 2SC458 transistor or 2SC2308 for an amplifier design, engineers and system integrators should:
- Confirm which model’s collector voltage ratings match the circuit’s expected conditions.
- Set bias and operating current using the circuit requirements, rather than treating maximum ratings as normal operating values.
- Review power dissipation at the expected ambient temperature and installation conditions.
- Account for the specified hFE range and grade when circuit behavior depends on current gain.
- Check the TO-92 lead assignments and verify the latest applicable product specification before final design or purchase.
Conclusion
The 2SC458 and 2SC2308 offer a defined set of electrical characteristics for low-frequency amplifier applications, but their differences—particularly in collector voltage ratings and gain groupings—matter during component selection. By checking test conditions, thermal limits, gain spread and package pinout, design teams can make a more informed assessment of whether either transistor fits a particular circuit. The datasheet also cautions that product specifications may change, so confirming the current specification is an important step before final design and use.