Access Official Technical PDF

Share Summary:LinkedInEmail

A PFM step-up regulator can raise a low input voltage to a regulated output while keeping control-circuit current low. For engineers designing compact power supplies, the choice of switching method and external components affects efficiency, output ripple and load capability. The S-8351 and S-8352 families illustrate two implementation options: an integrated power MOSFET or a controller that drives an external transistor.

Both families use pulse frequency modulation (PFM), with a reference source, oscillator, comparator and control circuitry. Their intended applications include portable equipment and other systems that need a step-up supply. Selecting a suitable configuration requires looking beyond the nominal output voltage to the load range, shutdown needs, switch arrangement and behavior of the inductor and output capacitor.

How PFM step-up regulation works

A boost converter stores energy in an inductor while its switching transistor is on. When the transistor turns off, the inductor releases energy through a diode to the output capacitor and load. The regulator monitors the output and controls switching to maintain the target voltage. In a PFM design, regulation is achieved by controlling switching pulses rather than relying only on a fixed-frequency, fixed-duty cycle.

The S-8351/8352 series has a nominal oscillation frequency of 100 kHz. In A, B and D types, the duty ratio automatically shifts between 50% at light load and 75% at higher output current. The transition is smooth through the intermediate load region. This approach is intended to limit pulse skipping and help manage ripple across changing loads. C types instead use a fixed 75% duty ratio; the datasheet notes that ripple at light load is higher than with the duty-switching types, while efficiency is better.

The device family specifies startup at 0.9 V minimum at an output current of 1 mA. Typical operating current is 23.2 μA for a 3.3 V output condition, while the shutdown current specification is a maximum of 0.5 μA for versions with shutdown. These figures are device specifications under stated conditions, not a substitute for evaluating the complete power stage in its intended application.

Choosing the switch and control configuration

Integrated or external transistor

The S-8351 integrates the power MOSFET. It provides a compact way to build a step-up supply with an external inductor, diode and capacitors. A protection circuit turns off the built-in MOSFET if the CONT pin voltage exceeds its limit.

The S-8352 provides an EXT output for driving an external transistor. This arrangement is intended for applications requiring higher output current, but the transistor and its surrounding circuit become important parts of the design. An N-channel MOSFET or an NPN bipolar transistor can be used. For a MOSFET, gate capacitance and threshold voltage matter; the datasheet recommends evaluating startup current in the actual circuit and notes that the series does not provide overcurrent protection for the external MOSFET. For an NPN design, transistor gain and base resistance affect drive capability and efficiency.

Match the type to system requirements

  • A type: automatic 50%/75% duty-ratio control and a shutdown input. The shutdown pin is active high for normal operation and low to stop the internal circuits.
  • B type: automatic duty-ratio control without a shutdown function.
  • C type: fixed 75% duty ratio without shutdown.
  • D type: automatic duty-ratio control with separate VDD and VOUT pins, but no shutdown function. This can support externally adjusted output voltage arrangements.

Output voltage options are selected by product variant. The stated selection range is 2.0 V to 6.5 V for A, B and C types, and 1.5 V to 6.5 V for D types. The D configuration separates the IC supply input from the output-voltage sensing pin; the datasheet recommends a VDD supply of at least 1.8 V for stabilizing output voltage and oscillation frequency, with additional conditions for variants set below 1.9 V.

External components shape converter performance

Component selection is central to boost converter design. The datasheet gives an inductance range of approximately 22 μH to 1 mH and recommends minimizing inductor DC resistance, with a value below 1 Ω. A larger inductance can reduce peak current but may make step-up operation from a low input voltage more difficult. A smaller value can increase peak and output current while reducing inductance efficiency. The core must withstand the peak current without magnetic saturation.

The diode should have a low forward voltage, specified as below 0.3 V, fast switching speed of 500 ns maximum, reverse-voltage capability of at least the output voltage plus the diode forward voltage, and a current rating that meets or exceeds peak inductor current.

Use an input capacitor to reduce power-supply impedance and help stabilize input current. The output capacitor smooths the pulsed energy delivered by the boost stage. The datasheet recommends at least 10 μF and emphasizes selecting a large capacitance with low equivalent series resistance (ESR) to reduce ripple. The appropriate value depends on output voltage, load current and the ripple requirements of the application.

Layout, validation and operating precautions

Place the inductor, diode and capacitors as close to the IC as practical. Switching regulators can exhibit ripple, spike noise and startup inrush current; their behavior depends on the selected components, circuit impedance and PCB layout. A schematic or reference component set alone does not guarantee successful operation.

Validation should cover the intended input-voltage range, load changes, startup and shutdown behavior, temperature and the completed PCB assembly. Check that switching-transistor dissipation remains within the package’s allowable power dissipation, and account for the possibility of temporary supply-voltage drops when inrush current flows. For D types, verify the VDD/VOUT arrangement and any external output-setting resistors in the actual design.

Conclusion

PFM step-up regulators offer a practical approach to low-voltage power conversion when low control current and a broad load range are important design considerations. The key decisions are whether to use an integrated or external switch, which duty-ratio and shutdown options fit the system, and how to size the inductor, diode and capacitors. Careful component selection, close placement of the power-stage parts and testing under real operating conditions are essential to achieving a stable, suitable supply.

Access Official Technical PDF

About The Author