Access Official Technical PDF

Share Summary:LinkedInEmail

An LCD bias power supply must generate a higher voltage than its input source while maintaining a controlled output for the panel. The S-8330/8331 series addresses this task with a CMOS PWM step-up switching regulator intended for LCD bias generation and other compact equipment. Its adjustable output, shutdown input, and low external component count make it a useful reference for engineers evaluating a boost-converter design.

The series accepts an input from 2.0 V to 9.0 V and supports model-dependent output ranges extending to 30 V. Selection depends on required output current, switching frequency, and whether the design should use an integrated or external switching transistor. Those choices influence the surrounding inductor, diode, capacitor, and control circuitry.

How the S-8330/8331 step-up regulator works

The regulator uses pulse-width modulation (PWM). During each switching cycle, energy is stored in an inductor while the switching transistor is on. When the transistor turns off, the inductor releases energy through a diode to the output capacitor and load. The control circuit adjusts pulse width in response to operating conditions while the switching frequency remains nominally fixed for a given variant.

This differs from pulse-frequency modulation approaches that may skip pulses at light loads. In the S-8330/8331, pulse width changes while frequency remains steady, allowing output ripple associated with switching to be filtered. The output capacitor’s capacitance and equivalent series resistance (ESR) affect ripple, so component selection is part of the regulation design rather than a secondary detail.

An internal soft-start function limits startup inrush and helps control output-voltage overshoot as step-up operation begins. The specified typical oscillation frequency is 180 kHz for A versions and 50 kHz for B versions. The series also includes an 8-bit electric volume circuit for setting the output voltage over a 12 V adjustment span.

Choosing between S-8330 and S-8331 variants

The S-8330 integrates the switching transistor, while the S-8331 drives an external transistor through its EXT pin. The datasheet positions these options for different load requirements:

  • S-8330B: Uses a 50 kHz oscillator and has lower quiescent current than the A version. It is intended for very low output-current applications, particularly around 0.1 mA or below.
  • S-8330A: Uses a 180 kHz oscillator and an integrated switching transistor. It is aimed at output currents from approximately 1 mA to 10 mA.
  • S-8331A: Uses a 180 kHz oscillator and an external switching transistor, targeting output currents of 10 mA or more.

These are selection guidelines, not substitutes for checking the operating conditions of a specific design. For example, the listed S-8330 output-current specification is 5 mA at VIN = 5 V and VOUT = 30 V. The S-8331 can support higher-current designs when paired with an appropriate external transistor and circuit components. A datasheet application circuit illustrates a 40 V, 20 mA LCD-panel supply using an S-8331, external feedback components, and a switching transistor.

Setting and controlling the output voltage

The electric volume receives serial data through VDIN and VCLK. Data is shifted in on clock edges, then transferred to the output-setting circuit when the VSTRB strobe is asserted. The output voltage is adjustable across 256 digital codes, with a specified 12 V adjustment range. The output-voltage range available from a device depends on its model designation.

Initialize the electric-volume register deliberately at startup. Its contents are uncertain when power is first applied. The datasheet warns that starting step-up operation before resetting the register can produce the maximum output voltage, potentially exposing connected equipment to an unintended level. A recommended sequence is to hold the shutdown input low, reset the register, and then enable step-up operation. If an unexpected maximum output could cause a problem, a pull-down resistor on the shutdown pin is recommended.

The shutdown pin is active low. Pulling it low stops step-up operation and internally connects VOUT to ground; the electric-volume circuit is excluded from the circuits that stop. This behavior should be considered at system level: current can flow through the input-side inductor and diode toward ground during shutdown, so a separate current-cutoff switch may be needed in some designs. The pin has no internal pull-up or pull-down, so it should not be left floating. If unused, connect it to VIN.

External components and layout considerations

Inductor value affects both available output current and efficiency. The recommended ranges are 22–100 μH for the S-8330A and 47–220 μH for the S-8330B. The designer must also check the inductor’s allowable current against the calculated peak switch current. Exceeding the inductor’s current capability can cause magnetic saturation, reduce efficiency, and place excessive current stress on the IC.

For the diode, the datasheet calls for low forward voltage, switching speed of 500 ns maximum, reverse-voltage capability of at least VOUT plus the diode forward voltage, and a current rating that meets or exceeds peak inductor current. At the output, use a capacitor with adequate capacitance and low ESR to help control ripple. The datasheet gives approximately 10 μF as a standard capacitance for both input and output capacitors, while noting that input capacitance should be selected with the power-source impedance in mind.

Keep the inductor, diode, and capacitors close to the IC, and make the ground path to VSS as short as possible. Resistance or inductance in this path can cause the IC’s ground potential to vary with switching current. Because ripple and spike noise depend substantially on the selected components and physical implementation, verify performance on an assembled design under its actual operating conditions.

Practical implications for LCD bias design

The S-8330/8331 series combines a wide input range, adjustable output, and shutdown control in an 8-pin SSOP package. Applying it successfully means matching the variant to the load, sizing the inductor and diode for peak current, managing output ripple through capacitor selection, and using a safe startup sequence for the programmable output. These checks help engineers and integrators assess whether the regulator architecture fits a particular LCD bias power supply and identify the circuit-level details that require validation before deployment.

Access Official Technical PDF

About The Author