Access Official Technical PDF

Share Summary:LinkedInEmail

In air-conditioned buildings, a refrigerant leak is an unlikely event when equipment is correctly installed and maintained, but system design still needs to account for the possibility. Refrigerant leak detection systems can identify a leak, provide audible and visual warning, and—in compatible configurations—initiate pump-down and isolate refrigerant. For engineers and building operators, selecting the right arrangement means considering room coverage, alarm requirements, the refrigerant circuit and the intended response to a detected leak.

Why refrigerant leak detection matters

BS EN 378 provides safety guidance for assessing refrigerant concentration if the full refrigerant charge were to escape into an occupied space. The whitepaper gives 0.44 kg/m³ as the critical concentration for R410A. Detection and alarm provisions are particularly relevant where a leak could affect a small occupied space, such as a hotel room.

A detection system can provide an audible and visual alert when refrigerant is detected, giving occupants and staff notice of a potential leak. The alarm arrangement must be considered as part of the overall compliance design: for example, the described aspirated panels include a sensor, but require additional local audible and visual alarms for BS EN 378 compliance.

Leak mitigation can also support environmental objectives. BREEAM Pollution Prevention Assessment (Pol 01) addresses pollution associated with refrigerant leakage. Detection and pump-down options may help a project achieve recognition in this area, but any credit or recognition is subject to evaluation by an accredited BREEAM assessor.

Choosing a refrigerant detection system

Detection options range from a sensor installed in each room to an aspirated panel that samples several spaces through tubing. The appropriate approach depends on the building layout, the number of rooms to monitor, alarm requirements and the selected sensing technology.

Room-based semiconductor detection

A semiconductor arrangement uses one sensor in each monitored space. The described KSGD-01 units combine refrigerant sensing with a local visual and audible alarm and can operate as standalone devices or connect to a remote alarm panel. This approach places detection at the room level, which can be suitable when spaces are monitored individually.

Multi-room aspirated detection

An aspirated system draws samples from multiple rooms through sampling tubes to a central panel. Room faceplates provide sample points, and local alarms can be added where required. The system information describes panels configured for 8, 16 or 32 channels, with options to sample two rooms per channel; the stated maximum coverage is up to 64 rooms, depending on configuration.

Because a central panel serves several spaces, aspirated detection can reduce the need for a separate sensing panel in every room. In City Multi R2 heat recovery VRF installations, sampling tubes and alarm wiring can be routed alongside refrigerant pipework. Design still needs to account for the sampling layout, room terminations, calibration points and local alarm provision.

Semiconductor and infrared sensing

The system range described uses semiconductor or infrared detection. A semiconductor sensor responds to a change in electrical resistance when the surrounding gas composition changes. The whitepaper identifies this option for clean, open environments such as offices and hotels.

Infrared detection works by measuring how gases absorb different wavelengths of infrared light. The described aspirated detector uses an infrared emitter and sensor to analyse a gas sample. Technology selection should follow the intended application and system configuration rather than being treated as interchangeable without review.

How pump-down and isolation work

Detection can be paired with a pump-down control system on eligible City Multi R2 heat recovery VRF installations. When connected to the leak detection system, the control panel provides the link to the VRF system and controls the pump-down sequence. The stated automatic pump-down availability applies to City Multi R2 heat recovery models PURY, YHM, YJM and YKM; it should not be assumed to apply to other systems.

Actuated ball valves provide an additional isolation function. One valve is installed on each of the high- and low-pressure refrigerant pipes between the outdoor unit and branch controller. During and after pump-down, the valves isolate refrigerant in the system to help minimise the effect of a leak.

The control panels are available for systems with one to eight outdoor units. Detection components can be used with standalone or aspirated arrangements, but the complete design needs to coordinate the detector, control panel, outdoor unit connection, branch controller and valves. Commissioning is required for pump-down systems.

Design and commissioning considerations

Before specifying a solution, project teams should establish the rooms requiring coverage, the detection technology, the alarm locations and whether pump-down is applicable to the selected VRF equipment. They should also confirm the intended panel capacity and the routing of sampling tubes and alarm wiring.

  • Check the occupied-space risk and applicable BS EN 378 requirements.
  • Confirm whether the design uses room-based sensors or a multi-room aspirated panel.
  • Include local audible and visual alarms where the selected arrangement requires them.
  • Verify compatibility before specifying automatic pump-down and actuated isolation valves.
  • Plan for system commissioning and engage the relevant design and installation professionals.

Detailed system design should be reviewed with the manufacturer’s local sales office, and electrical selections must be made by a qualified professional in accordance with current regulations and site conditions.

Conclusion

Refrigerant detection is both an occupant-safety measure and a design consideration for managing the consequences of a leak. Standalone semiconductor sensors and multi-room aspirated systems offer different ways to monitor spaces, while compatible City Multi R2 installations can add automatic pump-down and refrigerant isolation. Matching detection, alarms and mitigation to the building and equipment—and commissioning the completed system—helps ensure the intended response is properly integrated into the project.

Access Official Technical PDF

About The Author