Access Official Technical PDF

Share Summary:LinkedInEmail

Linear encoders turn mechanical displacement into electrical position feedback, supporting numerical control (NC) systems in machine tools, precision stages and inspection equipment. Choosing among linear encoders involves more than matching a measurement range: engineers also need to understand how the scale detects motion, how its signals integrate with the controller, and how calibration supports measurement accuracy.

How linear encoders detect displacement

Many linear scale systems use a graduated glass scale as the measurement reference. A detector reads the scale as it moves, and changes in the detected light or magnetic coupling are converted into electrical signals representing displacement. The sensing method influences the encoder’s construction and the way it interacts with its operating environment.

Photoelectric sensing: reflective and transmissive designs

In a reflective photoelectric encoder, an LED and collimator lens direct light toward gratings on an index scale and the graduated scale. Light reflected from the scale produces interference fringes at a receiving device. As the scale moves, the fringes shift, changing the received light and producing sinusoidal electrical signals.

A transmissive design uses light passing through the scale instead. The LED and receiving device sit on opposite sides, with the scale gratings modulating the light. Movement shifts the resulting interference pattern, which the receiver converts into signals. In the described assembly-type system, an interpolation circuit subdivides the sinusoidal output to produce square-wave pulses for position measurement.

Other sensing approaches

Electromagnetic induction scales determine movement through changes in coupling between coils. An exciter coil in the moving sensor induces current in coils arranged on the scale; the resulting magnetic coupling varies with position and generates a sinusoidal signal. Interpolation can then divide that signal to provide finer measurement resolution.

A different optical approach uses two-sided telecentric imaging to capture the scale grating as an image. The stated design uses deep focal depth to increase allowance for variation in the gap between scale and detector, while a wide imaging range provides allowance for some contamination or slight scale damage. These are design characteristics, not substitutes for checking the specific operating and installation requirements of an application.

Why calibration matters to linear encoder accuracy

An encoder’s stated accuracy depends on the reliability of the calibration process used to evaluate it. High-accuracy length measurement requires control of environmental influences, including temperature changes and vibration, as well as a dependable measurement reference.

The calibration facility described for these scales is built underground on bedrock, where temperature and humidity fluctuations and external vibration are kept to a minimum. Its ultra-precision length measuring machine uses a laser interferometer with the light path in a vacuum to reduce sources of uncertainty. The system is used to produce master scales, evaluate accuracy and support research. Its measurement results are traceable to national standards through the stated calibration framework and recognized through international interlaboratory comparisons.

For system designers, the practical point is that encoder accuracy is not only a property of the scale itself. Calibration capability, installation conditions and the measurement chain all matter when position feedback is used for precision motion control.

Matching the scale system to the application

NC linear scales are used in applications including machine tools, semiconductor and lithography equipment, electron microscopes, electronic component inserters, flat-panel-display inspection and scanning stages. These systems can support fully closed-loop positioning, where feedback comes from the measured movement of the machine axis rather than relying only on motor feedback.

Selection should account for the application’s travel, required resolution, maximum movement speed and controller interface. The system overview includes both separate-type scales and assembly-type units, with signal options such as sinusoidal outputs, square-wave pulses and absolute systems. Available measurement ranges, resolutions and response limits vary by model; the specification for the chosen unit should therefore be checked against the machine’s operating requirements.

  • Travel and mounting: Confirm that the effective measurement range and physical scale configuration fit the axis and available installation space.
  • Feedback interface: Verify that the output signal and reference-point arrangements are compatible with the controller and required motion sequence.
  • Speed and resolution: Check the model-specific response speed and resolution together, rather than considering either value in isolation.
  • Environment and installation: Review the operating limits and mounting conditions, including factors that can affect scale-to-detector alignment or gap.

Setup features can also affect commissioning. For example, the ST46-EZA description includes a push-button signal-adjustment function and a signal-strength indicator, allowing adjustment without an oscilloscope or PC. Such features should be treated as model-specific; they are not common to every scale system.

Plan the complete measurement chain

Reliable position feedback depends on the scale, detector, signal processing, controller and mechanical installation working as a system. Understanding the sensing principle helps clarify how displacement becomes an electrical signal, while calibration establishes confidence in the measurement reference. Engineers and integrators can use those considerations, alongside travel, speed, resolution and interface requirements, to select an encoder suited to the machine’s task.

The practical implication is straightforward: define the motion-control requirements first, then verify that the complete scale system—not just its headline accuracy—fits the application and can be properly installed and integrated.

Access Official Technical PDF

About The Author