Access Official Technical PDF

Share Summary:LinkedInEmail

Short-wave infrared (SWIR) sensing can support applications such as imaging and optical communications, but detector material and fabrication choices affect performance and integration complexity. Research on tellurium SWIR photodetectors points to a different materials approach: air-stable, solution-synthesized tellurium nano-flakes paired with optical cavities that increase and tune light absorption. The demonstrated devices cover much of the SWIR range, while also highlighting the engineering trade-offs involved in using a narrow-band-gap material with relatively weak absorption at longer wavelengths.

Why explore tellurium for SWIR detection?

Conventional SWIR detectors commonly rely on III–V semiconductors such as indium gallium arsenide. These materials can deliver strong performance, but their growth and fabrication can be complex. Two-dimensional and quasi-two-dimensional materials are being investigated as alternatives because their surfaces and thickness scaling can offer useful device properties. However, some candidate materials have practical limitations: black phosphorus, for example, can degrade rapidly in ambient conditions and high-quality crystals are typically obtained by mechanical exfoliation.

Tellurium offers a distinct structure. Its atoms form helical molecular chains, with van der Waals forces between the chains. The research describes tellurium as a true one-dimensional material assembled into a quasi-two-dimensional nano-flake. This chain-based structure, together with its small band gap and reported air stability, makes it a candidate for infrared optoelectronics.

The nano-flakes were produced using a hydrothermal solution process. The resulting material included flakes with thicknesses in the tens-of-nanometers range, and microscopy and diffraction measurements indicated single-crystalline flakes. This solution-based synthesis is a materials-processing advantage under investigation; it does not, by itself, establish that finished detectors are ready for manufacturing at scale.

Electrical properties of tellurium nano-flakes

In field-effect transistor measurements, thin tellurium flakes showed predominantly p-type transport. A 12 nm-thick device had a reported hole mobility of 450 cm2 V-1 s-1 at 300 K, increasing to 1,430 cm2 V-1 s-1 at 77 K. These measurements indicate that the material can support effective carrier transport in thin devices. Mobility increased as temperature fell, with the measured trend consistent with phonon scattering limiting mobility in the tested devices.

Optical characterization and temperature-dependent electrical measurements placed the material’s indirect band gap at approximately 0.31 eV. The band gap is relevant to the detector’s spectral range: it helps set the long-wavelength response, while the optical absorption and device structure also shape how effectively incident light produces a measurable electrical signal.

How optical cavities improve tellurium SWIR photodetectors

An indirect band gap can make absorption relatively weak in part of the SWIR range. The measured absorption coefficient for tellurium was lower at longer wavelengths than below approximately 1.6 μm. To address this limitation, the researchers placed thin tellurium flakes on an optical cavity made from a gold back reflector and an alumina (Al2O3) spacer.

The gold layer reflects light back through the semiconductor, while the alumina thickness sets the cavity’s optical behavior. In this device design, the alumina also functions as the gate dielectric. Adjusting its thickness changes the wavelength at which absorption is enhanced. In practical terms, cavity design becomes part of detector spectral tuning rather than a separate packaging consideration.

The demonstrated cavity substrates shifted the peak response across the SWIR: reported examples tuned peak responsivity from 1.4 μm to 2.4 μm, with corresponding values of 13 A/W and 8 A/W. The devices had a cutoff wavelength of 3.4 μm. A separately characterized device reached a room-temperature responsivity of 16 A/W at 1.7 μm; the reported optimized room-temperature specific detectivity was on the order of 2 × 109 cm Hz1/2 W-1.

What engineers should take from the results

For engineers and system integrators evaluating emerging infrared sensors, these results illustrate how material properties and optical-stack design can work together. The semiconductor’s response is not determined by the band gap alone: cavity geometry can increase absorption at a selected wavelength, while electrical bias influences the measured photoresponse. The tellurium devices’ responsivity was strongly gate-dependent and was maximized near the bias condition where drain current was minimized.

The flakes also showed polarization-dependent response, consistent with tellurium’s anisotropic crystal structure. Light polarized relative to the molecular-chain direction produced different responses, particularly near the indirect band edge. This characteristic may be relevant where polarization sensitivity is useful, but it is also a design factor for systems that require consistent response regardless of light orientation.

Frequency-response measurements showed a measurable photoresponse up to 100 kHz, with a reduction relative to low-frequency response rather than a clear 3 dB cutoff within the tested range. The researchers associated the behavior with photoconductive gain and possible trap-state effects. This means that responsivity, noise, and dynamic response should be considered together when assessing a detector for a specific sensing task.

Conclusion: a materials-and-optics design opportunity

Solution-synthesized tellurium nano-flakes combine a small indirect band gap with high measured hole mobility and demonstrated SWIR photoconduction. Optical cavities based on gold and alumina address weak long-wavelength absorption and provide a way to tune peak response by changing spacer thickness. The findings establish a research-stage device approach, not a drop-in industrial sensor. For future development, the practical questions include how to reproduce the material and cavity characteristics across larger areas, and how the resulting responsivity, noise, polarization behavior, and speed align with application requirements.

Access Official Technical PDF

About The Author