A single supply may not provide every voltage rail required by an industrial control or data-acquisition circuit. The ICL7660 voltage converter addresses one common need: generating a negative supply from a positive input using a compact CMOS charge-pump circuit. With two external capacitors, it can also be configured for positive voltage doubling. Its usefulness depends on understanding the device’s operating range, output impedance, and load limitations before incorporating it into a design.
What the ICL7660 and ICL7660A do
The ICL7660 and ICL7660A are monolithic CMOS power-supply circuits that convert a positive input into a complementary negative output. The ICL7660 operates with inputs from 1.5V to 10V, while the ICL7660A extends the upper end of the input range to 12V. In a negative-conversion configuration, the nominal output polarity is opposite the input: a positive supply produces a negative rail of approximately the same magnitude, subject to loading and circuit losses.
The devices integrate an oscillator, voltage regulator, level translator, logic network, and four MOS power switches. Two external capacitors provide the charge-pump and charge-reservoir functions. This makes the circuit relatively simple to implement, but the output is not equivalent to a separately regulated power supply: its voltage changes with load, component characteristics, and operating conditions.
How the CMOS charge pump creates a negative rail
The conversion process alternates between two switching phases. During the first phase, the pump capacitor charges from the positive supply. During the second, internal switches reposition that capacitor so its stored charge is transferred to the reservoir capacitor with reversed polarity. Repeating this cycle maintains the negative output.
The switching action is managed internally. A logic network monitors the output and adjusts the substrate bias of internal switches to help prevent latchup. The ICL7660 family’s oscillator runs at a nominal 10kHz under the stated 5V conditions. Designers can alter oscillator behavior by adding a capacitor at the OSC terminal or by driving it with an external clock. With external clocking, the pump frequency is half the clock frequency; the datasheet also specifies a 1kΩ series resistor for the clock connection.
Capacitors, output impedance, and ripple
The pump capacitor transfers charge, while the reservoir capacitor supplies the load between transfer cycles. Their values and equivalent series resistance (ESR) affect output performance. The datasheet describes 10µF capacitors as a typical starting point for basic applications. Larger capacitance can reduce the capacitive contribution to output impedance and help limit ripple, but low ESR is also important: capacitor resistance can significantly increase the effective output impedance.
In practical terms, the converter behaves approximately like a voltage source in series with an output resistance. That resistance includes the internal switch resistance, the effects of switching frequency and pump capacitance, and capacitor ESR. As load current rises, the voltage drop across this effective resistance increases. The output therefore may sit noticeably below its unloaded value, especially when the load is heavy or the capacitors are not well suited to the application.
Output ripple has both an ESR-related component and a component caused by the reservoir capacitor discharging into the load between charge transfers. Selecting suitable capacitors and evaluating the expected load are therefore essential design steps. Increasing switching frequency can reduce one contribution to output impedance, but it does not automatically improve performance in every case; the datasheet notes that the pump capacitors may not have enough time to fully charge at higher frequencies, depending on their value and circuit conditions.
Operating-range and layout decisions
Configure the LV pin for the supply range
For low-voltage operation, the LV pin should be connected to ground to bypass the internal series regulator. At supply voltages above 3.5V, the LV pin should be left open to support latchup-resistant operation and avoid device damage. The device has separate low- and higher-voltage operating conditions, so the intended supply range should guide this connection.
Observe polarity and startup precautions
When using polarized capacitors, connect the positive terminal of the pump capacitor to CAP+ and the positive terminal of the reservoir capacitor to ground, as specified in the datasheet. The device also cautions against applying inputs from external supplies before the converter is powered, and against allowing its output to go more positive than ground. Such conditions can cause latchup. A diode across the reservoir capacitor is identified as a way to prevent latchup from this output condition.
Short-circuit conditions also require attention. The datasheet allows continuous output short duration only when the supply is 5.5V or lower; extended shorting above that supply level should be avoided. The absolute maximum ratings are not normal operating targets, so designs should remain within the specified operating conditions.
Other configurations: doubling, paralleling, and cascading
Besides generating a negative rail, the ICL7660 can be used as a positive voltage doubler with external diodes and capacitors. The resulting output is approximately twice the input voltage minus the forward-voltage drops of the two diodes. The device can also combine negative conversion and positive doubling, though sharing the charge-pump driver introduces additional source impedance.
For applications requiring lower output resistance, multiple devices may be paralleled. Each device needs its own pump capacitor, while the reservoir capacitor can be shared. Cascading devices can produce a larger negative voltage multiplication, but each stage has finite efficiency; the datasheet identifies ten devices as a practical limit for light loads. Neither arrangement removes the need to assess the resulting voltage drop and load requirements.
Choosing the converter for an automation design
The ICL7660 family can be useful when a circuit needs a modest negative rail or a simple voltage-multiplication function from an existing supply. Before selecting it, confirm the input voltage and required output polarity, estimate load current, and account for capacitor ESR, output ripple, and effective output resistance. Check the LV-pin configuration and startup conditions as well. These steps help determine whether an unregulated charge-pump output is suitable or whether the application requires a different supply approach.
For engineers and system integrators, the practical value of the ICL7660 voltage converter lies in its straightforward conversion topology—not in providing a high-current or tightly regulated rail by itself. Matching the circuit to the load and respecting its operating guidance are key to achieving predictable performance in control, processor, and data-acquisition designs.